Porter-Cable PCSRW4800 Instruction Manual Download Page 11

11

Drywall anchors and anchor screws (16) are included with this rack; however, different wall materials 

require different types of fasteners. Use fasteners suitable for your specific type of wall. If you are 

uncertain about what type of fasteners to use, please contact your local hardware store.

Each wire grid (9) consists of two sides – a “short” side and “long” side. If you plan on sliding objects 

on and off of the shelf from the front of the rack, then we recommend having the “short” side of the 

grid facing upward. If you plan on sliding objects from the side of the rack, then we recommend 

having the “long” side facing upward.
The use of a step ladder is recommended for installing components at the top of the Workbench.

Serious injury or death can occur from the rack tipping over. To prevent this, the rack must be 

secured to a wall, especially in earthquake-prone areas, where surfaces are uneven, and where 

children and/or pets are present.

PART 2: WALL ANCHORING INSTRUCTIONS (FIG. S-U)

PART 3: LAMINATE DECK, WIRE GRID, AND LOCKING SHELF PIN 

INSTRUCTIONS (FIG. V-X)

NOTICE

NOTICE

1.  There are two wall mount bracket assemblies (16) to be used to secure the Workbench. One will 

be installed on the backside of the crossbeam (4) right above the fold-up drawer (19). The other 

one will need to be installed on the backside of the top crossbeam (4).

2.  Take the U-shaped bracket and rock it up at an angle to attach it to the bottom inner channel 

of the crossbeam (4). Once attached, the back portion will sit flush against the inside of the 

crossbeam (4). (Fig. S)

3.  Once attached, the U-shaped bracket can be moved from side to side [in between the two 

safety straps (6)]. This allows for it to be attached to a 2 x 4 in the wall. (Fig. T)

4.  The L-shaped bracket has two sets of four square holes that allow you to adjust the distance of 

the rack to the wall. Use two carriage bolts (11) and two 10 mm nuts (12) to attach the L-shaped 

bracket to the bottom of the U-shaped bracket. (Fig. U)

1.  It is recommended that a laminated deck (8) is placed on the crossbeams (4) right above the 

drawer (19) to serve as a work surface. To install the laminate deck (8), place it on the top ledge 

of the crossbeams (4). If seated properly, it will “pop” into place and lay evenly. (Fig. V)

2.  The last laminate deck (8) can be placed on any preferred set of crossbeams (4). The 

recommended location is on the top set of crossbeams (4).

3.  To install the wire grid (9), place the wire grid (9) onto the top ridge of a set of crossbeams (4). 

If seated properly, the grids will “pop” into place and lay evenly. Install the two wire grids (9) on 

the two remaining sets of crossbeams (4).

WARNING

Fig. S

Fig. T

Fig. U

 

Different wall materials require different types of fasteners. Use fasteners suitable for your 

specific type of wall. If you are uncertain about what type of fastener to use, then please contact 

your local hardware store. 

16

16

4

4

4

16

16

ROCK BRACKET UPWARDS

Summary of Contents for PCSRW4800

















Reviews: