background image

13 - ENG

MAInTenAnCe

Disconnect  air  line  from  tool,  engage  trigger  lock  and  remove  

fasteners  from  magazine  before  making  adjustments  or  personal  injury  may 

result.

DAIly MAInTenAnCe CHART

ACTIOn

WHy

HOW 

Lubricate tool with 5-7 

drops of PORTER-CABLE 

Pneumatic Tool Oil

Prevents failure 

of o-rings

Insert drops into air fitting 

on end cap of tool

Drain compressor tanks 

and hoses daily

Prevents accumulation 

of moisture in 

compressor and nailer

Open petcocks or other 

drain valves on compressor 

tanks. Allow any accumulated 

water to drain from hoses

Clean magazine, magazine 

release and contact 

trip mechanism.

Permits smooth 

operation of magazine, 

reduces wear and 

prevents jams.

Blow clean with compressor 

air. The use of oils, lubricants 

periodically or solvents is 

not recommended as they 

tend to attract debris.

Before each use, check 

to insure all screws, 

nuts and fasteners are 

tight and undamaged. 

Prevents jams, leaks 

and premature failure 

of tool parts.

Tighten loose screws or other 

fasteners using the appropriate 

hex wrench or screwdriver. 

CleAnInG

  Never use solvents or other harsh chemicals for cleaning the non-

metallic parts of the tool. These chemicals may weaken the materials used in these 

parts. Use a cloth dampened only with water and mild soap. Never let any liquid get 

inside the tool; never immerse any part of the tool into a liquid.

RepAIRS

For assistance with your tool, visit our website at www.portercable.com for a list of 

service centers, or call the PORTER-CABLE Customer Care Center at 1-888-848-5175 

(U.S. & Canada Only).
 

SeRvICe

ReplACeMenT pARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service 

website at http://servicenet.deltaportercable.com/. You can also order parts from 

your nearest PORTER-CABLE Factory Service Center or PORTER-CABLE Authorized 

Warranty Service Center. Or, you can call our Customer Care Center at 1-888-848-5175 

(U.S. & Canada Only). 

SeRvICe AnD RepAIRS

All quality tools will eventually require servicing and/or replacement of parts. For 

information about PORTER-CABLE, its factory service centers or authorized warranty 

service centers, visit our website at www.portercable.com or call our Customer Care 

Center at 1-888-848-5175 (U.S. & Canada Only). All repairs made by our service centers 

Summary of Contents for FC350B


















Reviews: