Page 16
Emhart Teknologies - 50 Shelton Technology Center, Shelton CT 06484 - Tel. (203) 924-9341 - Fax (800) 225-5614
Safety Data
SEAL LUBE
(P/N:
PSA075508P
)
LUBRIPLATE
®
130-AA
Manufactured by:
Fiske Brothers Refining Co.
Phone: (419) 691-2491
Emergency: (800) 255-3924
ALVANIA
®
EP Grease 1
Prod Code: 71124
Manufactured by:
Shell Oil Products
Phone: (877) 276-7285
MSDS#: 57072E-5
First Aid:
SKIN:
Remove any contaminated clothing and
wash with soap and warm water. If
injected by high pressure under skin,
regardless of the appearance of its size,
contact a physician IMMEDIATELY.
Delay may cause loss of affected part
of body.
INGESTION:
Call a physician immediately. Do not
induce vomiting.
EYES:
Flush with clear water for 15 minutes or
until irritation subsides. If irritation
persists, consult a physician.
Fire:
FLASH POINT: COC- 400
°
F
Cool exposed containers with water.
Use foam, dry chemical, carbon dioxide
or water spray.
Environment:
WASTE DISPOSAL:
Assure conformity with applicable
disposal regulations. Dispose of
absorbed material at an approved
waste disposal facility or site.
SPILLAGE:
Scrape up grease, wash remainder with
suitable petroleum solvent or add
absorbent.
Handling/ Storage:
Keep containers closed when not in
use. Do not handle or store near heat,
sparks, flame or strong oxidants.
Lubriplate
®
is a registered trademark of Fiske
Brothers Refining Company.
JAW LUBE
(P/N: PRG510-130)
SUNPAR 107
Manufactured By:
Sunoco, Inc.
Emergency Phone: (800) 424-9300
First Aid:
SKIN:
Wash with soap and water until no
odor remains. If redness or
swelling develops, obtain medical
assistance. Wash cloths before
reuse.
INGESTION:
Do not induce vomiting! Do not
give liquids! Obtain emergency
medical attention. Small amounts
that accidentally enter mouth
should be rinsed out until taste of it
is gone.
EYES:
Flush with water.
Fire:
FLASH POINT: Greater than 200
°
F
Can be made to burn. Use water
spray, regular foam, dry chemical or
carbon dioxide.
Environment:
WASTE DISPOSAL:
Do not flush to drain or storm sewer.
Contract authorized disposal
service.
SPILLAGE:
Contain Spill. Absorb onto inert
material. Shovel, sweep or
vacuum spill.
Handling/ Storage:
NFPA Class IIIB Storage. Avoid
prolonged breathing of mist or
vapor. Avoid prolonged or
repeated contact with skin. Avoid
contact with eyes. Wash thoroughly
after handling.
HYDRAULIC OIL
(P/N: PRG540-130)
MOBIL DTE 26
Manufactured By:
ExxonMobil Corporation
Emergency Phone: (609) 737-4411
MSDS Fax on Demand:
(613) 228-1467 MSDS # 602649-00
Shell TELLUS 68
Manufactured By:
SOPUS Products
Health Information: (877) 504-9351
MSDS Assistance:
(877) 276-7285 MSDS # 402288L-0
Distributed By:
Emhart Teknologies
Phone: (203) 924-9341
First Aid:
SKIN:
Remove contaminated clothing and
shoes and wipe excess from skin.
Flush skin with water, then wash with
soap and water. If irritation occurs,
get medical attention.
INGESTION:
Do not induce vomiting. In general, no
treatment is necessary unless large
quantities of product are ingested.
However, get medical attention.
EYES:
Flush with water. If irritation occurs, get
medical attention.
Fire:
FLASH POINT: 390
°
F/198.9
°
C
Material will float and can be re-ignited
on the surface of water. Use water fog,
‘alcohol foam’, dry chemical or carbon
dioxide (CO2) to extinguish flames. Do
not use a direct stream of water.
Environment:
SPILLAGE:
Soak up residue with an absorbent such
as clay, sand or other suitable material.
Place in a non-leaking container and
seal tightly for proper disposal.
Handling:
Wash with soap and water before
eating, drinking, smoking, applying
cosmetics or using toilet. Properly
dispose of leather articles such as
shoes or belts that cannot be
decontaminated. Use in a well
ventilated area.
Storage:
Store in a cool, dry place with adequate
ventilation. Keep away from open
flames and high temperatures.
Please refer to the actual MSDS for complete safety and handling
information. These can be obtained from the point of purchase.
