background image

1.

 

Safety Precautions 

1.1

 

Ensure the product is used within the specification (Max. 15A). 

1.2

 

Do not dismantle the device without authorization to avoid 

unexpected accident. 

1.3

 

Do not operate the controller near any high temperature, high 

humidity, explosive or inflammable field. 

1.4

 

Children are not allowed to operate the device. Keep children 

away from the controller.   

1.5

 

Do not use in salt water or corrosive water, the metal NTC probe 

will be slowly damaged by salt water or acid-alkali water. 

1.6

 

NOTE: If the relays are used over capability, contact fusing or 

burning may occur. Please use the relays within their rated load.

 

 

2.

 

Overview 

What is TC-15A? 

TC-15A  is an easy-to-use, safe and reliable dual relay output 

temperature controller. It can be connected to both heating and cooling 

loads at the same time to control temperature.     

 

This unit can  be used as over temperature protection or automatic 

temperature control system for various tasks. Such as Sous-vide, 

Terrarium  Heat Control,  Heat Mats,  Germination,  Fermentation  and 

Brewing. 

Summary of Contents for TC-15A










Reviews: