manualshive.com logo in svg

PolyScience F25N0A101B, Operator'S Manual, Page: 2 / 14

Share
Download
PolyScience F25N0A101B Operator'S Manual Download Page 2

110-064 

1 

Table of Contents 

Introduction.............................................................................................................................................................. 2 

General Information................................................................................................................................................. 2 

General Safety Information .................................................................................................................................... 2 
Safety Recommendations...................................................................................................................................... 3 
Regulatory Compliance and Testing...................................................................................................................... 3 
Unpacking Your Low Temperature Cooler ............................................................................................................ 3 
Contents................................................................................................................................................................. 3 

Installation................................................................................................................................................................ 4 

Electrical Power ..................................................................................................................................................... 4 
Immersion Probe (IP) Coolers ............................................................................................................................... 4 

Positioning the Immersion Probe Assembly....................................................................................................... 4 

Flow Through (FT) Cooler...................................................................................................................................... 5 

Tubing Connections ........................................................................................................................................... 5 
Suitable Fluids .................................................................................................................................................... 6 

Normal Operation .................................................................................................................................................... 7 

Immersion Probe Coolers ...................................................................................................................................... 7 
Flow Through Coolers............................................................................................................................................ 7 

Routine Maintenance & Troubleshooting ............................................................................................................. 8 

Cleaning Exterior Surfaces .................................................................................................................................... 8 
Cleaning the Refrigeration Condenser Fins........................................................................................................... 8 
Draining Residual Oil from the Immersion Probe Assembly.................................................................................. 8 
Troubleshooting ..................................................................................................................................................... 9 

Technical Information ........................................................................................................................................... 11 

Performance Specifications ................................................................................................................................. 11 

Equipment Disposal (WEEE Directive)................................................................................................................ 12 

Service and Technical Support ............................................................................................................................ 12 

Warranty ................................................................................................................................................................. 13 

 

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for F25N0A101B















Reviews:

No comments