background image

Modes of Operation:

Handset Only Mode

 (Audio through handset only with

volume control):

 

Auto Answer Mode

: Call comes in, video is auto-

  answered, and audio is muted until handset is picked
 up.

 

Standard Answer Mode

: Call is only answered when

  the handset is picked up.

 

Auto Dial Mode

: System audio dials a preset number

  when the handset is lifted. Preset is labeled “auto dial.”
  Configure Favorite Entry with First Name: 

Auto 

and

  Last Name: 

Dial

.

 

Hang Up Call

: System hangs up a call when the

  handset is placed on hook, with a built-in three
  second delay in case of accidental user error.

Hands-Free Mode

 (No handset, therefore no volume

control): System auto answers only. No other features.
The call is disconnected by the far-end hanging up the
call or using the ir remote locally. Audio through
speakers only.

Both Handset and Hands-Free Mode

 (Includes volume

control): System auto answers with audio through
speakers. Pick up handset and audio goes to handset
only (privacy). Pre-define upon installation: To
eliminate the handset from hanging up calls (h
hands free operation), set the following in Favorite
entry, First Name: 

handset

, Last Name: 

hangupoff , 

to not

disconnect the call when the handset is returned to the
cradle. A dummy IP address may be required to store
Favorite entry. Use 127.0.0.1 or other.

Mains Input Rating:

Voltage: 100-240VAC, 50-60Hz
Current: 2.7A (max)

Physical size and weight:

23-1/2” W x 19” H x 6-5/8” D without handset
27” W x 19” H x 6-5/8” D with handset
55 lbs.

6

Polycom® RealPresence® Video Protect 500 Setup Sheet

Regulatory Notices:

 

This equipment is intended for indoor use only.

   Do not use a power cord that is damaged. This could cause

 

fire or electric shock. Contact the manufacturer for a

 

replacement cord, if necessary.

   Only use a power cord which is appropriately rated and

 

approved relevant to the country of use.

   When connecting to the mains supply, connect only to an

 

earthed supply outlet which is installed near the equipment

 

and is easily accessible.

  

If the mains supply is required to be made directly to the

 

building electrical installation, only a qualified electrician

 

should carry out this work in accordance with local wiring

 

rules and regulations.

   Keep ventilation openings free from any obstructions.

  The ambient operating temperature rating of this equipment

 is 

0 - 40ºC and should not be exceeded.

  

Do not immerse the system in any liquid or place any liquids

 

on it.

  

Do not spray liquids directly onto the system when cleaning.

 

Always apply the liquid first to a static-free cloth.

  

For further information concerning the individual components

 

of this equipment, please refer to the respective product

 literature.

  

For support or service, please contact your Polycom®

 

distributor or go to Polycom Support at

 www.polycom.com/support. 

Summary of Contents for RealPresence Video Protect 500









Reviews: