background image

 

 

OFF 

00s < x < XXs 

Nothing 

ON 

00s < x < 60s 

Search for source base/repeater 

ON 

60s < x < XXs 

Search for any base/repeater in the system 

 

Button 

In the below table the action of the button press is presented. 

Button 

Press 

Action 

00s < x < 02s 

Nothing 

02s < x < 06s 

Delete registration 

Old registration is deleted, and a new registration procedure is 
started. 

18s < x < 60s 

Enable or disable repeater monitor beep tone in handset during call. 

60s < x < XXs 

Nothing 

 

LED 

LED 

Indication 

Action 

GREEN 

Off 

Power Off 

GREEN 

Slow flash 

Unlocked, Searching for base station 

GREEN 

Double flash 

Registration/subscription mode and searching for open base station – 
registering procedure. 

GREEN 

Steady on 

Locked to base station and ready for use - idle 

RED 

Off 

No handset relayed by repeater 

RED 

n

 flash 

n

 handset relayed by repeater 

RED 

Steady on 

1. Registration procedure timed out after 5 min. 

2: When key is held pressed the LED will light up in 2 sec. to indicate 
that releasing the key will delete registration, LED turns off after 4 
more sec. 

RED/GREEN 

Flashing 
Red/Green 

Recovery mode – repeater is locked to base station/repeater without 
repeater mode activated. 

1: Sync. Source base station/Repeater not found (Manual mode). 

2: Timeout during RPN allocation due to busy base station/Repeater. 

 

 

 
 
 
 

Summary of Contents for Rove R8














Reviews: