background image

 

 

FCC Warning

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to 
part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable  protection  against  harmful 
interference  in  a  residential  installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 
radio  communications.  However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
 
—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help. 

 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) 
This device may not cause harmful interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation. 
 
For Repeater 
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This 
equipment should be installed and operated with minimum distance 20cm between the radiator& your body. 
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter 
located or operating in conjunction with any other antenna or transmitter. 
 
ISEDC Warning

 

This device complies with ISEDC licence-exempt RSS standard(s). Operation is subject to the following two 
conditions: 
(1) this device may not cause interference, and 
(2) this device must accept any interference, including interference that may cause undesired operation of 
the device. 
 
Le  présent  appareil  est  conforme  aux  CNR  d'ISEDC  applicables  aux  appareils  radio  exempts  de 
licence.L'exploitation est autorisée aux deux conditions suivantes : 
(1) l'appareil nedoit pas produire de brouillage, et 
(2)  l'utilisateur  de  l'appareil  doit  accepter  tout  brouillage  radioélectrique  subi,  même  si  le  brouillage  est 
susceptible d'en compromettre le fonctionnement. 
 
ISEDC Radiation Exposure Statement: 
 
For Repeater 
This equipment complies with ISEDC radiation exposure limits set forth for an uncontrolled environment. This 
equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 
 
Déclaration d'ISDEC sur l'exposition aux radiations: 
 
Pour répéteur  
Cet équipement est conforme aux limites d'exposition aux radiations ISEDC définies pour un environnement 
non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le 
radiateur et votre corps. Cet émetteur ne doit pas être situé ou fonctionner conjointement avec une autre 
antenne ou un autre émetteur. 

Summary of Contents for Rove R8














Reviews: