P
P
P
P
R
R
R
R
E
E
E
E
P
P
P
P
A
A
A
A
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
F
F
F
F
O
O
O
O
R
R
R
R
U
U
U
U
S
S
S
S
E
E
E
E
• Unscrew the self-refilling tank cap (
7
)
(Fig.1) and fill the tank with about 560 cc
of water by using the filler bottle (
U
) sup-
plied.
• Water by its nature contains magnesium,
mineral salts and other deposits which in
hard water areas can contribute to
limescale build up in the tank. To avoid
these problems, it is necessary to swill out
with tapwater and empty the generator
tank after every 3 or 4 uses.In very hard
water areas we recommend the use of our
KALSTOP FP 2003, a special natural-
base decalcifier which inhibits and breaks
down limescale. This is a preventive
against limescale build-up and protects
the metal walls of the steam generator
tank. KALSTOP is available from Polti
dealers or by mail-order from your Polti
Service Centre.
• Carefully screw on the sealing cap (
7
) to
hand tight.
• Lift the water container handle (
22
) un-
hooking it from its position (Fig. 2) and re-
move the container (
20
) (Fig. 3).
• Turn the container handle (
22
) as shown
in figure 4, so as to remove the “Eco Ac-
tiveFilter” water filter assembly (
23
).
• Fill the water container (
20
) with about 1,2
litres of simple tap water until the MAX
level indicator (
21
) is reached, as in fig. 5.
• Put the filter assembly (
23
) back into place
in the water container (
20
) returning it to
its initial position.
• Replace the water container back into po-
sition.
• Support the handle (
22
) until it hooks into
its place on the water container (
20
).
O
O
O
O
P
P
P
P
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
• Open the flap of the built-in socket (
9
); fit
the monobloc plug (
B2
) by pushing it,
without pressing the button, until you hear
the click of the locking mechanism, then
make sure it is well locked (fig.6).
• To disconnect the monobloc plug (
B2
)
from the appliance, push the button (
B3
)
and pull the monobloc so as to separate it
from the appliance (fig.6a).
• Connect the plug to the mains.
Operation with steam + suction
• Press the main switch (
1
), the first level of
suction indicators (
5
) will start to flash.
• Press the boiler switch (
2
) which will light
up.
• Wait for the pressure indicator lamp (
4
) to
light up. When it does the Vaporetto
Lecoaspira will be ready to generate
steam.
• Press the suction button (
A4
) on the han-
dle (
A2
). The suction function will start up
at the minimum speed and the first stage
of the indicator lamp set (
5
) will stop flash-
ing and remain on. For correct use of the
suction function read the section “Suction
control/ switching off”.
Note:
The handle (
A2
) has a safety button
(
A3
) which when set in locked position
prevents activation of the delivery of
steam. If the appliance is left temporarily
unattended while it is in an activated con-
dition, please remember to place the
safety button (
A3
) in the locked position.
To resume delivery, return the button to its
initial position.
• You can supply steam by pressing the
steam button (
A5
) on the handle. At the
same time you can also control suction by
pressing the suction button (
A4
).
Operation with suction only
• If you wish to use the suction function only,
press the main switch (
1
), the first level of
the suction indicators (
5
) will start to flash.
• By pressing the suction button (
A4
) on the
handle (
A2
), the suction fan will start to
run at the lowest speed and the first stage
of the indicator lamp (
5
) will stop flashing
and remain steadily lit. For correct use of
the suction read the section “Suction con-
trol/switching off”.
Operation with steam only
• Press the main switch (
1
), the first level of
LECOASPIRA AS720 LUX
56
VT AS720KUX - M0S07341 1M07.qxp 04/07/2006 16.42 Pagina 56
