cling, treatment and environmentally compati-
ble disposal helps to prevent negative impact
on the environment and human health and
promotes the recycling of the materials ma-
king up the product. For more information on
available collection facilities, contact your lo-
cal waste collection service or the shop where
you bought this appliance.
P
P
R
R
E
E
P
P
A
A
R
R
A
A
T
T
I
I
O
O
N
N
F
F
O
O
R
R
U
U
S
S
E
E
• Unscrew the patented safety cap (
7
) (Fig.1)
and fill the generator with 1,3 litres of water,
using the special anti-drip filler bottle (
U
).
• Water by its nature contains magnesium,
mineral salts and other deposits which in
hard water areas can contribute to
limescale build up in the tank. To avoid
these problems, it is necessary to swill out
with tapwater and empty the generator tank
after every 3 or 4 uses.In very hard water
areas we recommend the use of our
KALSTOP FP 2003, a special natural-base
decalcifier which inhibits and breaks down
limescale. This is a preventive against
limescale build-up and protects the metal
walls of the steam generator tank.
KALSTOP is available from Polti dealers or
by mail-order from your Polti Service Cen-
tre.
• Carefully screw on the sealing cap (
7
) to
hand tight.
• Lift the water container handle (
22
) unhook-
ing it from its position (Fig. 2) and remove
the container (
20
) (Fig. 3).
• Turn the container handle (
22
) as shown in
figure 4, so as to remove the “Eco Active-
Filter” water filter assembly (
23
).
• Fill the water container (
20
) with about 1,2
litres of simple tap water until the MAX level
indicator (
21
) is reached, as in fig. 5.
• Put the filter assembly (
23
) back into place
in the water container (
20
) returning it to its
initial position.
• Replace the water container back into posi-
tion.
• Support the handle (
22
) until it hooks into its
place on the water container (
20
).
O
O
P
P
E
E
R
R
A
A
T
T
I
I
O
O
N
N
• Open the flap of the built-in socket (
9
); fit
the monobloc plug (
B2
) by pushing it, with-
out pressing the button, until you hear the
click of the locking mechanism, then make
sure it is well locked (fig.6).
• To disconnect the monobloc plug (
B2
) from
the appliance, push the button (
B3
) and pull
the monobloc so as to separate it from the
appliance (fig.6a).
• Connect the plug to the mains.
Operation with steam + suction
• Press the main switch (
1
), the first level of
suction indicators (
5
) will start to flash.
• Press the water boiler - terracotta/parquet
button (
2
) once only.
• The pressure indicator light (
4
) will flash un-
til the boiler reaches working pressure, then
stay on steadily. When it does the Va-
poretto Lecoaspira will be ready to generate
steam.
• Press the suction button (
A4
) on the handle
(
A2
). The suction function will start up at the
minimum speed and the first stage of the in-
dicator lamp set (
5
) will stop flashing and re-
main on. For correct use of the suction func-
tion read the section “Suction control/
switching off”.
Note:
The handle (
A2
) has a safety button
(
A3
) which when set in locked position pre-
vents activation of the delivery of steam. If
the appliance is left temporarily unattended
while it is in an activated condition, please
remember to place the safety button (
A3
) in
the locked position. To resume delivery, re-
turn the button to its initial position.
• You can supply steam by pressing the
steam button (
A5
) on the handle. At the
same time you can also control suction by
pressing the suction button (
A4
).
Operation with suction only
• If you wish to use the suction function only,
press the main switch (
1
), the first level of
the suction indicators (
5
) will start to flash.
• By pressing the suction button (
A4
) on the
handle (
A2
), the suction fan will start to run
at the lowest speed and the first stage of the
indicator lamp (
5
) will stop flashing and re-
LECOASPIRA 705
56
E
E
N
N
G
G
L
L
I
I
S
S
H
H
E
E
N
N
G
G
L
L
I
I
S
S
H
H
LECOASPIRA 705 - M0S07835 1N03:Layout 1 20/04/2007 11.40 Pagina 56
