VAPORELLA PROFESSIONAL SYSTEM
29
E
E
N
N
G
G
L
L
I
I
S
S
H
H
H
H
O
O
W
W
T
T
O
O
C
C
O
O
N
N
N
N
E
E
C
C
T
T
/
/
D
D
I
I
S
S
C
C
O
O
N
N
N
N
E
E
C
C
T
T
V
V
A
A
P
P
O
O
R
R
E
E
L
L
L
L
A
A
T
T
O
O
T
T
H
H
E
E
B
B
O
O
A
A
R
R
D
D
To asseble the Vaporella to the board pro-
ceed as follows:
• Place Vaporella on to the board so that the
fixing pins (
W
) are directed outwards
(Fig.A).
• Insert the board connector (
S
) into the Va-
porella connector (
T
) to make the electrical
connection.
• To fix the connection, lower the locking de-
vice (
T1
) located on the Vaporella connec-
tor (Fig. B) until it locks.
• Turn the Vaporella and insert the two fixing
pins (
W
) into the tubes under the board (
X
)
pushing it until it locates securely into the
board (Fig. C).
• Screw up the two locking devices (
R
) to fix
the Vaporella to the board.
Before using Vaporella carefully check that
it is correctly connected to the board.
• To disconnect Vaporella proceed inversely
to the above description.
NOTE:
while connecting and disconnecting
Vaporella place the iron on the right iron stand
(
U
) As described in paragraph “how to close
the machine”.
P
P
R
R
E
E
P
P
A
A
R
R
A
A
T
T
I
I
O
O
N
N
F
F
O
O
R
R
U
U
S
S
E
E
1a. Rest the board on the floor.
2a. Pull the opening handle (
O
) upwards and
open the board (
N
), supporting it as it ri-
ses to the right height position. Adjusting
the regulation handle (
O
), you can bring
the board up to the required height.
3a. Insert the cable stand (
M
) in its location
(fig. 1).
4a. Place the cable (iron power supply -
steam tube) (
E
) in its support (fig. 2). The
appliance is also equipped with a rigid
iron rest (
F
).
5a. Unscrew the patented safety cap (
A
) and
fill the boiler with about 0,9 litres of water
using the special funnel (
I
) making sure
that it does not overflow (fig. 3). Normal
tapwater can be used. However, as hard
water by its nature contains limestone,
which may cause a build-up of limescale
in the tank, in hard water areas we recom-
mend the use of our natural-base decalci-
fier KALSTOP FP 2003.
6a. Retighten the cap fully and carefully.
Ensure the patented safety cap is fully
and correctly screwed on, otherwise you
may experience steam escaping from
around the cap.
7a. Connect the power supply cable (
D
) into
an earthed power supply of the correct
voltage.
8a. Switch on the boiler and iron by pressing
the switches (
B
) and (
C
) which will light up
together with the pressure indicator light
(
K
) (fig. 4).
9a. Wait for a few minutes to allow the ironing
surface to reach the operating tempera-
ture.
10a.By pushing the function switch (
P
) (Fig.4)
on position (
I
), the board will allow you to
swell the clothes with a “hot blow”, in or-
der to be able to gently skim with the iron
the most delicate clothes, ironing them
with steam only.
11a.By pushing the function switch (
P
) (Fig.4)
on position (
II
), the board will hold the
clothes to the surface and eliminate the
residual humidity.
Note:
to avoid condensation inside the iron-
ing board we recommend you always use the
suction function while steam ironing.
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
F
F
O
O
R
R
U
U
S
S
E
E
Check the manufacturer’s label on the gar-
ment, and interpret the symbol on the label as
follows:
Steam ironing allowed
For dry ironing, set the iron temperature
on •••
Steam ironing allowed
For dry ironing, set the iron temperature
on ••
Check the fabric's resistance to steam iro-
ning, dry ironing allowed with temperature
set on •
- do not iron
- steam ironing or treatment not allowed
VL PROFESSIONAL SYSTEM M0S05865 1O09:FEV 1000-950.qxd
29/06/2009
10.58
Pagina 29
