manualshive.com logo in svg

Polartec Heat Blanket, Instruction Manual, Page: 12 / 13

Share
Download
Polartec Heat Blanket Instruction Manual Download Page 12

Care and Cleaning

CAUTION: Always disconnect the power cord and the blanket cord before
washing your blanket. Do not wash the wireless remote control and 
snap-on base. Carefully follow all washing instructions.

• Do not dry-clean your blanket. Dry cleaning solvents may damage 

the blanket.

• Do not use bleach, fabric softeners, or cleaning fluids.

• Do not use a wringer.

• Do not iron the blanket.

• Do not use mothballs or sprays of any kind.

• Do not turn the blanket ON until it is completely dry.

Machine Washing

1

. Machine wash warm, delicate cycle.

2

. Do not use bleach or fabric softeners.

Machine Drying

CAUTION: Do not use commercial dryers or the dryers at your local coin-
operated laundry. They get too hot and will damage the blanket.

1

. Tumble dry air only, no heat, for 

90

minutes.

2

. Stretch to original size and lay flat over a bed.

Cleaning the Base Unit and Wireless Remote Controls

1

. Unplug the base unit’s power cord from the electrical outlet.

2

. Wipe the base unit and remotes with a damp cloth. Plug the base unit power

cord back in again.

12

INSTRUCTION MANUAL OP  8/20/01  10:45 AM  Page 10

Summary of Contents for Blanket














Reviews:

No comments