Operating Elements
1
2
3
4
180°
1 LED panel
2
Power (ON / OFF) / 3 brightness levels
3 Non-slip foam
4 Charging connector 12V/DC 1 A
Foam base can leave marks on sensitive surfaces.
Operation
a) Connect to Power Supply
• Connect the supplied power adaptor to the charging connector 12V/DC 1 A (4) at the rear of the lamp and
the other end to a power outlet.
b) LED Lighting
• Touch (2) to turn the LED light on.
• Touch again to cycle through brightness levels (low, medium, high).
• The LED light will turn off after cycling through all brightness levels.
c) Flexible Lighting Angle
The lighting angle can be adjusted so that it is directed towards where you need it most. Flexible section
shown in the diagram “Operating Elements”.
Risk of damage. Do not use force to bend the stem past 180° or bend outside the flexible
section. Please hold the base of the lamp while adjusting to prevent it from falling over.
Care and Cleaning
• Turn the product off and disconnect it from the mains.
• Let the product cool down to room temperature before you start cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
•
Clean the product with a dry, fibre-free cloth.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste.
At the end of its service life, dispose of the product in accordance with applicable regulatory
guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical Data
a) Lamp
Input voltage / current ........................... 12 V/DC, 1 A
Power consumption .............................. 7 W
Light source .......................................... LED, 36 pcs
Colour temperature ............................... 6000 – 6500 K
Lighting modes ..................................... Low (50 lumen), Medium (130 lumen), High (380 lumen)
Operating conditions
............................. -5 to +40 °C, 10 – 80 % relative humidity
Storage conditions ................................ -10 to +45 °C, 10 – 80 % relative humidity
Dimensions (L x W x H)
........................
145 x 145 x 625 mm
Weight .................................................. 628 g
b) Power adapter
Input...................................................... 100 - 240 V/AC, 50/60 Hz, 0.4 A
Output
................................................... 12 V/DC, 1000 mA, 12 W
Operating Instructions
LED Desk Lamp 7 W
Item No. 1546854
Intended Use
This lamp features advanced technology including non-visible flickering, selectable brightness levels, and
flexible lighting angles. The foam base pad prevents slipping and protects sensitive surfaces from getting
scratched.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use
can result in short circuits, fires, electric shocks or other hazards. Read the instructions carefully and store
them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery Content
• Lamp
• Power adapter
•
Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of Symbols
The symbol with the lightning in the triangle is used if there is a risk to your
health, e.g. due to an electric shock.
The symbol with the exclamation mark in the triangle is used to indicate important information in
these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
Safety Instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
a) General Information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
•
Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, steam and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
•
Consult an expert when in doubt about the operation, safety or connection of the appliance.
•
Maintenance, modifications and repairs must only be completed by a technician or an
authorised repair centre.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
•
Risk of fire! Do not cover the product during use. The product gets hot during use.
b) Power adaptor
• Connect the appliance to a wall socket that can be accessed easily.
• As power supply, only use the supplied mains adaptor.
•
Only connect the power adaptor to a normal mains socket connected to the public supply.
Before plugging in the power adaptor, check whether the voltage stated on the power adaptor
complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use
the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or damaged
by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them. This poses
a risk of injury.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
These operating instructions are published by CEI Conrad Electronic International (HK) Limited, 18th Floor, Tower 2,
Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, New Territories, Hong Kong. All rights including translation reserved.
Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require
the prior written approval by the editor. Reprinting, also in part, is prohibited. The operating instructions reflect the current
technical specifications at time of print.
© Copyright 2018 by CEI Conrad Electronic International (HK) Limited
*1546854_v3_0318_02_JC_m_4L
Distributed by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau
