background image

31

FEATURES AND CONTROLS

WARNING

Do not start or operate an ATV with sticking or improperly

operating throttle controls, which could cause an accident and

lead to severe injury or death.
Always contact your dealer for service repairs if throttle problems

arise.
Failure to check or maintain proper operation of the throttle

system can result in an accident if the throttle lever sticks during

operation.
Always check the lever for free movement and return before

starting the engine. Also check occasionally during operation.

Throttle Lever

Engine speed and vehicle

movement are controlled by

pressing the throttle lever. The

throttle lever (1) is spring loaded.

Engine speed returns to idle when

the lever is released.
This ATV is equipped with Polaris Electronic Throttle Control (ETC),

which is designed to reduce the risk of a frozen or stuck throttle. If the

throttle cable should stick in an open position when the operator

releases the throttle lever, the engine will stop, and power to the rear

wheels will cease.

WARNING

The Electronic Throttle Control (ETC) stops the engine in the

event of a throttle system malfunction and is provided for your

safety. Do not attempt to modify the ETC system or replace it

with any after market throttle mechanisms.

1

Summary of Contents for Trail Boss 9920770



























































































































Reviews: