background image

50

OPERATION

Break-In Period

The break-in period for your new Polaris ATV is defined as the first ten

hours of operation, or the time it takes to use the first two full tanks of

gasoline. No single action on your part is as important as following

the procedures for a proper break-in. Careful treatment of a new

engine will result in more efficient performance and longer life for the

engine. Perform the following procedures carefully.

CAUTION

Excessive heat build-up during the first three hours of operation

will damage close-fitted engine parts. Do not operate at full

throttle or high speeds for extended periods during the first three

hours of use.

CAUTION

Mixing brands or using a non-recommended oil may cause

serious engine damage. We recommend the use of Polaris

Premium 4 synthetic Oil or another 0W-40 API certified

SH

oil.

Never substitute or mix oil brands.

1. Fill the fuel tanks with gasoline. See page 39.
2. Check the oil reservoir level on the dipstick. See page 75. Add

oil if necessary to maintain the level between the safe and add

marks.

3. Drive slowly at first. Select an open area that allows room to

familiarize yourself with vehicle operation and handling.

4. Vary the throttle positions. Do not operate at sustained idle.
5. Perform regular checks on fluid levels, controls and areas outlined

on the daily pre-ride inspection checklist. See page 51.

6. Pull only light loads.
7. During the break-in period, change both the oil and the filter at 20

hours, 200 miles, or one month, whichever comes first.

Summary of Contents for Sprotsman MV7




































































































































Reviews: