manualshive.com logo in svg

Polaris Sportsman 850 2021, Owner'S Manual

Share
Download
Polaris Sportsman 850 2021 Owner'S Manual Download Page 12

CAUTION

This equipment complies with part 15 of the Federal Communications 

Commission (FCC) rules.

These requirements are intended to provide reasonable protection against 

harmful interference in a residential installation. This equipment generates, 

uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not 

occur in a particular installation.

If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on, the 

user is encouraged to try to correct the interference by one or more of the 

following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the 

party responsible for compliance could void the user’s authority to operate the 

equipment.

This vehicle may contain the following radio equipment or components that 
contain radio equipment:

COMPONENT

COMPONENT ID

MANUFACTURER

B1 Gauge Bluetooth

WT12

Silicon Labs

Hereby, Polaris Industries Inc. declares that the above radio equipment is in 
compliance with EU Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following 
internet address:

https://www.polaris.com/en-us/radio-conformity/

10

INTRODUCTION

Summary of Contents for Sportsman 850 2021





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands