manualshive.com logo in svg

Polaris Alpha, User Manual, Page: 42 / 56

Share
Download
Polaris Alpha User Manual Download Page 42

42 

 

8. Raw Measurement Recording and Post Processing 

 

For  post-processing,  both  base  data  and  rover  data  need  to  be  available.  The  base  data  can  be  (1) 

stored RTCM data received from RTK base station service or (2) stored SkyTraq raw measurement data 

from  Alpha  RTK  base.  The  RTK  rover  data  is  stored  SkyTraq  raw  measurement  data  from  Alpha  RTK 

rover.   

 

To store raw measurement data, the supplied 16GByte SD Card needs to be inserted into Alpha’s SD 

Card holder. To enable raw measurement recording, pressing the push button for 3 seconds until SD 

Card LED turns ON. When SD Card is recording the LED will flash. Pressing the push button for another 

3 seconds until SD Card LED ceases flashing will stop raw measurement recording. To avoid recording 

file corruption, always stop raw measurement recording before powering off Alpha. 

 

The  logged  raw  measurement  data  or  RTCM  data  can  be  converted  to  RINEX  format  using  v.2.4.3 

RTKLIB’s RTKCONV program. After converting base and rover logged data into standard RINEX format, 

they can be post-processed using RTKLIB’s RTKPOST or other post-processing software. 

 

 

Summary of Contents for Alpha

























































Reviews:

No comments