manualshive.com logo in svg

Polaris Alpha, User Manual, Page: 11 / 56

Share
Download
Polaris Alpha User Manual Download Page 11

11 

 

Figure 4-2 

 

4-2 RTK Survey and Data Collection 

 

Internet

Bluetooth

Rover

BT mode / switch on B

3

rd

 Party RTK Base 

with NTRIP caster

NTRIP 

client

3G/4G/LTE

Setup for GIS Data Collection

RTK

antenna

. . .

Alpha RTK

 

Figure 4-3

 

 

When used with Trimble or Leica RTK base station within 10Km distance, or Trimble or Leica RTK base 

station  with  Virtual  Reference  Station  (VRS)  service  as  shown  in  figure  4-3  for  RTK  survey  and  data 

collection, then only one Alpha RTK receiver is needed. It’s configured as RTK rover and connects to an 

Android  smartphone  via  Bluetooth.  User  can  then  run  the  free  Lefebure  NTRIP  Client  App  on  the 

smartphone  for  retrieving  3

rd

-party  RTK  base  station  data  over  Internet  and  sending  it  to  the  Alpha 

RTK receiver. With “MOCK Location” option enabled on the smartphone, GPS related location Apps on 

the smartphone will be able to use the more accurate position from Alpha RTK receiver. 

 

 

 

 
 

 

Summary of Contents for Alpha

























































Reviews:

No comments