background image

28

SAFETY

Operator Safety

WARNING

POTENTIAL HAZARD
Operating the ATV through deep or fast-flowing water.
WHAT CAN HAPPEN
Tires may float, causing loss of traction and loss of control, which

could lead to an accident or overturn.
HOW TO AVOID THE HAZARD
Avoid operating the ATV through deep or fast-flowing water. If it’s

unavoidable to enter water that exceeds the recommended

maximum depth (see page 59), travel slowly, balance your weight

carefully, avoid sudden movements, and maintain a slow and

steady forward motion. Do not make sudden turns or stops, and

do not make sudden throttle changes.
Wet brakes may have reduced stopping ability. Always test the

brakes after leaving water. If necessary, apply them several

times to let friction dry out the pads.

WARNING

POTENTIAL HAZARD
Operating this ATV with improper tires, or with improper or

uneven tire pressure.
WHAT CAN HAPPEN
Use of improper tires, or operation of the ATV with improper or

uneven tire pressure, could cause loss of control or accident.
HOW TO AVOID THE HAZARD
Always use the size and type of tires specified for the ATV.
Always maintain proper tire pressure as specified.

Summary of Contents for 2006 Sportsman 450







































































































































Reviews: