Polaris 2006 Predator 500 Owner'S Manual For Maintenance And Safety Download

Page: 91 / 189

EMISSION CONTROL SYSTEMS

Noise Emission Control System

Do not modify the engine, intake or exhaust components, as doing so may affect

compliance with U.S.A. EPA noise control requirements (40 CFR 205) and local noise

level requirements.

Operation on Public Lands in the U.S.A.

Your Polaris vehicle has a spark arrestor that was tested and qualified to be in accordance

with the USDA Forest Service Standard 5100-1C. Federal law requires that this spark

arrestor be installed and functional when the vehicle is operated on public lands.
Operation of off-road vehicles on public lands in the U.S.A. is regulated by 43 CFR 8343.

Violations are subject to monetary penalties. Federal regulations can be viewed online at

www.gpoaccess.gov/ecfr/.

Electromagnetic Interference

This spark ignition system complies with Canadian ICES--002.
This vehicle complies with European directives 97/24/EC and 89/336/EEC.

Summary of Contents for 2006 Predator 500






























































































































































































Search results

Summary of Contents for 2006 Predator 500

Reviews:

Related manuals for 2006 Predator 500

Brands by name

Popular brands

Polaris 2006 Predator 500, Owner'S Manual For Maintenance And Safety

Search results

Summary of Contents for 2006 Predator 500

Reviews:

Related manuals for 2006 Predator 500

Brands by name

Popular brands