Polaris 2005 99 Ranger Owner'S Manual Download

Page: 93 / 104

MAINTENANCE

Headlight Beam

The headlight beam can be adjusted up and down.

1. Place the vehicle on a level surface with the headlight approximately 25’ (7.6

m) from a wall.

2. Measure the distance from the floor to the center of the headlight and make a

mark on the wall at the same height.

3. Start the engine and turn the headlight switch to high beam.

4. Observe headlight aim. The most intense part of the headlight beam should

be aimed 2

″

(5.1 cm) below the mark placed on the wall in step 2.

NOTE:

Rider

weight must be included on the seat.

5. Loosen pivot bolts and adjust beam to desired position.

6. Tighten nut and bolt. Torque to 60 in. lbs.

Indicator Lamp Replacement

1. Unplug light from harness, depress lock-

ing tabs and remove from pod.

2. Install new light and reassemble pod.

Depress locking
tabs to remove.

Summary of Contents for 2005 99 Ranger









































































































Search results

Summary of Contents for 2005 99 Ranger

Reviews:

Related manuals for 2005 99 Ranger

Brands by name

Popular brands

Polaris 2005 99 Ranger, Owner'S Manual

Search results

Summary of Contents for 2005 99 Ranger

Reviews:

Related manuals for 2005 99 Ranger

Brands by name

Popular brands