background image

FOREWORD

This Arctic Cat Service Manual contains service, maintenance, and troubleshooting information for certain 2008

Arctic Cat ATV models (see cover). The complete manual is designed to aid service personnel in service-oriented

applications.

Arctic Cat offers additional publications (when they become available) to aid in servicing other ATV models. To

service models not included in this manual, please refer to the following publications:

2008 Y-12 Service Manual

2008 DVX/Utility 250 Service Manual

2008 366 Service Manual

2008 DVX 400 Service Manual

2008 700 Diesel Service Manual

2008 Thundercat Service Manual

This manual is divided into sections. Each section covers a specific ATV component or system and, in addition to

the standard service procedures, includes disassembling, inspecting, and assembling instructions. When using this

manual as a guide, the technician should use discretion as to how much disassembly is needed to correct any given

condition.

The service technician should become familiar with the operation and construction of each component or system

by carefully studying the complete manual. This manual will assist the service technician in becoming more aware

of and efficient with servicing procedures. Such efficiency not only helps build consumer confidence but also saves

time and labor.

All Arctic Cat ATV publications and decals display the words Warning, Caution, Note, and At This Point to

emphasize important information. The symbol 

! WARNING

 identifies personal safety-related information.

Be sure to follow the directive because it deals with the possibility of severe personal injury or even death. The

symbol 

! CAUTION

 identifies unsafe practices which may result in ATV-related damage. Follow the direc-

tive because it deals with the possibility of damaging part or parts of the ATV. The symbol 

„

NOTE:

 identifies

supplementary information worthy of particular attention. The symbol 

 

AT THIS POINT

 directs the tech-

nician to certain and specific procedures to promote efficiency and to improve clarity.

At the time of publication, all information, photographs, and illustrations were technically correct. Some photo-

graphs used in this manual are used for clarity purposes only and are not designed to depict actual conditions.

Because Arctic Cat Inc. constantly refines and improves its products, no retroactive obligation is incurred.

All materials and specifications are subject to change without notice.

Keep this manual accessible in the shop area for reference.

Product Service and

Warranty Department

Arctic Cat Inc.

© 2007 Arctic Cat Inc.

July 2007

®™ Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701

Back to TOC

FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983

www.mymowerparts.com

Summary of Contents for 500H1




































Reviews: