3
UK
Manual Defrost
The appliance will automatically run a defrost cycle every six hours.
To manually defrost the appliance:
1. Press and hold the DEFROST
button for 5 seconds.
2. The defrost cycle will start immediately and the Defrost LED illuminates.
The defrost will last a maximum of 30 minutes.
3. Waste water is collected in the waste water tray.
Lock/Unlock the Doors
A lock is fitted to the doors to ensure foodstuffs are kept secure within your
POLAR appliance.
Use the keys provided to lock/unlock the doors.
Cleaning, Care & Maintenance
•
Switch off and disconnect from the power supply before cleaning.
•
Clean the interior of the appliance as often as possible.
•
Do not use abrasive cleaning agents. These can leave harmful residues.
•
Clean the door seal with water only.
•
Always wipe dry after cleaning.
•
Do not allow water used in cleaning to run through the drain hole into
the evaporation pan.
•
Take care when cleaning the rear of the appliance. Sharp edges can cut.
•
A POLAR agent or qualified technician must carry out repairs if required.
Cleaning the Condenser
Periodically cleaning the condenser can extend the life of the appliance.
POLAR recommend that a POLAR agent or qualified technician clean the
condenser.
Troubleshooting
If your POLAR appliance develops a fault, please check the following table
before making a call to the Helpline.
Parameter
Name
Description
Range
=
19
Temperature Offset
Should there be any variance between measured and actual temperature, the measured
temperature can be offset to compensate
-20°C to 20°C
=
22
Unit of Measurement
Set whether the temperature is displayed in Centigrade or Fahrenheit
Centigrade (
0
) or Fahrenheit (
1
)
=
23
Compressor Operation
During Probe Failure
Set whether the compressor runs or remains Off during a temperature probe failure
Compressor runs (
1
)
Remains Off until fault fixed (
0
)
Runs intermittently with
parameters =
24
and =
25
(
2
)
=
24
Compressor ‘On’
Duration
Set the length of time the compressor runs during a temperature probe failure
1-99 minutes
=
25
Compressor ‘Off’
Duration
Set the length of time the compressor remains Off during a temperature probe failure
1-99 minutes
=
34
Initial Defrost After
Startup
(G591/G593/G595 only)
Set whether the appliance starts a defrost cycle 10 minutes after
startup or after the time programmed in parameter
d8
(Defrost Cycle Time Intervals)
Begins 10 minutes after startup
(
0
) or when programmed (
1
)
=
38
Minimum Temperature
Alarm
Set the display to flash should the inner temperature of the appliance drop beyond a specified
point from the programmed operating temperature
1°C to 50°C
Note: The cycle starts from the time the appliance is initially
powered up.
Note: Starting a manual defrost also resets the automatic
defrost timer.
The next automatic defrost will start six hours after the
manual defrost has finished.
Fault
Probable Cause
Action
The appliance
is not working
The unit is not switched on
Check the unit is
plugged in correctly
and switched on
Plug and lead are damaged
Call POLAR agent or
qualified Technician
Fuse in the plug has blown
Replace the fuse
Power supply
Check power supply
Internal wiring fault
Call POLAR agent or
qualified Technician
The appliance
turns on, but
the
temperature is
too high/low
Too much ice on the condenser
Defrost the appliance
Condenser blocked with dust
Call POLAR agent or
qualified Technician
Doors are not shut properly
Check doors are shut
and seals are not
damaged
Appliance is located near a heat
source or air flow to the
condenser is being interrupted
Move the refrigerator to
a more suitable location
Ambient temperature is too
high
Increase ventilation or
move appliance to a
cooler position
Unsuitable foodstuffs are being
stored in the appliance
Remove any excessive
hot foodstuffs or
blockages to the fan
Appliance is overloaded
Reduce the amount of
food stored in the
appliance
The appliance
is leaking water
The appliance is not properly
levelled
Adjust the screw feet to
level the appliance
The discharge outlet is blocked
Clear the discharge
outlet
Movement of water to the drain
is obstructed
Clear the floor of the
appliance
The water container is
damaged
Call POLAR agent or
qualified Technician
The drip tray is overflowing
Empty the drip tray
The appliance
is unusually
loud
The frame has become loose
Check and tighten all
nuts and screws
The appliance has not been
installed in a level or stable
position
Check installation
position and change if
necessary
