background image

11

AU

AU

Telephone Helpline: 1300225960

During storage:

•  the display shows the cabinet temperature
•  if chilling had a positive outcome, the LEDs 

 and 

 will be on; if 

chilling had a negative outcome, the LEDs 

 and 

 will be on and the 

LED 

 will flash. 

•  the parameter rA sets the operational set point 
•  press 

 several times to:

 

- display the message “nEg”

 

- exit the procedure, or leave for 15 seconds

To interrupt the 

cycle:

•  press 

 for 2 seconds

Test To Check Correct Pin Probe Insertion

•  Set-temperature cycles are preceded by a test step in order to check correct 

pin probe insertion.

•  If power is interrupted during the test, when power is restored, the test will 

start again from the beginning.

The test has two stages:

•  if the outcome of the first stage is positive, the second will not be run

•  if the outcome of the first stage is negative, the second will be run. 

•  The outcome of the first stage is positive if “the temperature measured by the pin probe - the 

temperature of the cabinet” is greater than the value set by parameter rc at least 3 times out of 5 (the 

comparison is made every 10 s); if parameter rc is set to 0, neither the first nor second stages will be 

run. 

•  The outcome of the second stage is positive if the difference “temperature measured by the pin probe 

- temperature of the cabinet” is greater by at least 1ºC/1ºF (with respect to the previous comparison) 

at least 6 times out of 8 (the comparison is made every “rd/8 s”)

If the outcome of the test is positive:

•  the cycle will be activated

•  the cycle will be started in timed mode
•  the LED 

 will flash

Setting The Configuration Parameters

The parameters are arranged on two levels.

To access the first 

level:

•  ensure the device is in “stand-by” mode and no procedures are running
•  press 

 and 

 for 4 s: the display will show “PA”

To access the 

second level:

•  access the first level
•  press 

 or 

 to select “PA”

•  press 

 

•  press 

 or 

 within 15 s to set “-19”

•  press 

 or leave for 15 s

•  press 

 and 

 for 4 s: the display will show “CA1”

CK640-A_A5_v1_20190507.indb   11

2019/5/7   15:55

Summary of Contents for CK640-A

















Reviews: