*1)
For more details see
Operating Diagrams.
*2) tEnP =1
:
°C
Temperature range.
tEnP =2
:
°F
Temperature range.
*3)
Sensor reading can be adjusted by pressing the
+
or
-
keys
HP34
SL 2.0
Temperature-Luminosity controller
Handbook
DAY SET TEMPERATURE SETTING.
Press
DAY TEMP
(key lamp flashes):
This messagge will be displayed instead of the
°Set Day temperature.
Press
+
or
-
to modify, press
DAY TEMP
to confirm.
MAIN SETTINGS (Run Mode)
NIGHT SET TEMPERATURE SETTING.
Press
NIGHT TEMP
(key lamp flashes):
This messagge will be displayed instead of the
°Set Night temperature.
Press
+
or
-
to modify, press
NIGHT TEMP
to confirm.
DAY/NIGHT CONDITION SETTING.
Press
LUMIN SET
(key lamp flashes):
This messagge will be displayed instead of the
% Set Day/Night condition.
Press
+
or
-
to modify, press
LUMIN SET
to confirm
*
.
These settings refer to the mode operation of the system and must be made on initial start-up:
press
- / +
together for at least one second: the message
C.O.S.t.
will be displayed.
Press than repeatly
LUMIN SET
until interested variable's message is displayed (see table
below) : variable value and related message will be displayed.
Press
+
or
-
to set a new value and then
LUMIN SET
to confirm.
The next system constant will then appear.
You can press
LUMIN SET
for a least two second to escape and return to the
Run Mode
.
COSt PROGRAMMING (System constants)
*
Down this luminosity
Night
condition is on: up this luminosity
Day
condition is on.
Luminosity is represented in
0.0-99.9
;
0.0
represents total dark,
99.9
represents maximum luminosity.
.
s
s
e
M
e
u
l
a
V
g
n
i
n
a
e
M
e
t
o
N
t
.
F
i
d
°
2
.
0
l
a
i
t
n
e
r
e
f
f
i
d
e
r
u
t
a
r
e
p
m
e
t
C
°
1
*
L
.
F
i
d
0
.
1
l
a
i
t
n
e
r
e
f
f
i
d
y
t
i
s
o
n
i
m
u
L
C
°
1
*
r
u
d
.
t
'
0
)
s
e
t
u
n
i
m
(
y
a
l
e
d
n
o
i
t
i
s
n
a
r
t
t
h
g
i
N
-
y
a
D
1
*
P
n
E
t
1
=
)
F
°
2
=
,
C
°
1
=
(
n
o
i
t
a
t
n
e
s
e
r
p
e
r
e
r
u
t
a
r
e
p
m
e
T
2
*
E
t
.
d
A
°
0
.
0
)
-
r
o
+
(
n
o
i
t
c
e
r
r
o
c
e
r
u
t
a
r
e
p
m
e
t
t
u
p
n
I
C
°
3
*
u
L
.
d
A
0
.
0
)
-
o
+
(
n
o
i
t
c
e
r
r
o
c
r
o
s
n
e
s
y
t
i
s
o
n
i
m
u
l
t
u
p
n
I
C
°
3
*
This processor comes already with a preset variable settings.
To reset it to these settings, switch processor off then press
LUMIN SET
key and keep it pressed
giving power on: release
LUMIN SET
key when on the screen appear
boot
message.
d.SEt =25.0° n.SEt =20.0°
L.SEt = 30.0
The
COSt
values are shown in
COSt
paragraphs.
PRESET PROGRAMS
Lamp.
State
N° Relay
Contact
HEAT
Heat On
1
3-4
COOL
Cool On
1
4-5
DAY
Day condition On
NIGHT
Night condition On
The lights situated at the bottom of the display show the state of the various relays as set out below.
STATUS INDICATION LAMPS
As it company policy to continually improve the products the Manufacturers
reserve the right to make any modifications thereto without prior notice.
They cannot be held liable for any damage due to malfunction.
26.10.00
In some start-up conditions may be useful to work in "hand" mode.
Power off theprocessor, press
+
key and keep it pressed giving power on:
HAnd
message will be displayed (release now
+
key).
Push
+
until is displayed number required to be handed (see table relays "
N° Relay
") and push
LUMIN SET
for activing relay.
Pushing again
+
for increase relay number previous relay is disactivated.
You can press
LUMIN SET
for a least two seconds to escape and return to the
Run Mode
"HAND MODE"
diF.t
diF.t
diF.L
COOL
DAY
TEMP.
d.SEt
1/2 diFF
1/2 diFF
H E A T
NIGHT
TEMP.
n.SEt
1/2 diFF
1/2 diFF
DAY
CONDITION
LUMIN.
L.SEt
1/2 diFF
1/2 diFF
NIGHT
DAY
COOL
NIGHT
H E A T
DAY
NIGHT
CONDITION
DAY/
NIGHT
CONDITION
OPERATIVE DIAGRAMS
HEAT CONTACT
COOL CONTACT
LX LUMIN. PROBE
SX TEMP. PROBE
H=1500A
FUSE 4A T
HP34
H=1500A
FUSE 4A T
How to connect the line
Connect line on terminals
L-N
; protect supply with adeguate
fuse.
How to connect the sensors
Connect the sensors provided as shown in the diagram. For
remote connections use a standard 0.5-square millimeter
two-pole wire , taking great care over the connections, by
insulating and sealing the joins carefully.
-O.C.-
is displayed
when the temperature sensor wiring is open,
-S.C.-
is
displayed when the temperature sensor wiring is short circuit.
How to connect the contacts
Output contacts are N.O. (Normally Opened free of voltage)
on wich is apliable a 4AMP AC1 maximum load.
INSTALLATION
230V LINE
