When use the password to unlock: press pa # to confirm.
﹙
3
﹚
Restore factory default setting.
press 02 + # + programming code + #
﹙
4
﹚
Setup unlock way
：
(Factory default : read valid cards unlock)
Press 10 + # Read valid cards unlock
Press 11 + # Read fingerprint unlock
Press 12 + # input valid password unlock
Press 13 + # Read valid cards or input valid password unlock
Press 14 + # Read valid cards or fingerprint unlock
Press 15 + # input valid password or fingerprint unlock
Press 16+ # Read valid card
、
valid fingerprint or input valid password unlock
﹙
5
﹚
Setup unlock time(Factory default is 3 seconds
）
Press 17 + # + unlock time + # , Time : double digits (between 03-60s) ,unit : seconds.
（
6
）
Security mode:(Default setting: close)
Press 18 + # Close security function
Press 19 + # Open security function
Note: Input wrong programming code 5 times or invalid password 5 times
continuously,the system will dead lock 1 minute,the blue led fast flashing.
﹙
7
﹚
Add User card:
Press 20 + # + code + # + read card +#
Continuous add cards: Don’t need to press # after read the first card,can read the
second card directly,the code NO will be given automatically,press # to confirm after read
all user card. Card code is 4 unrepeatable No.
（
0001-1000
）
8
﹚
Delete user cards
：
Press 21 + # to delete all user card
Press 22 + # + read card +# delete the read card
Press 23 + # + input the card code + # delete the corresponding card
﹙
9
﹚﹙
9
﹚
Add the fingerprint
1 . press 30 + # + fingerprint code + #
2.press your finger,the buzzer sound 1 beep,then loosen your finger.
3. press your finger again,the buzzer sound 1 beep,then loosen your finger
4. If the buzzer sound 5 beep,then fingerprint add failure;if sound 1 beep,then
succeed.
5. Whether succeed or failure,need to press # to finish the command .(It is very
important)
1. Restore the factory setting:
Disconnect the power supply, press # key all the time,then connect the power
supply,when hints “DIDI” voice,then release your hand,the machine had been restored the
factory settings successfully. (Note:It only can restore the programming code,another
information can’t be restored.)
2. Enter the Programming Mode:
Press * + Programming code (factory default: 999999) + #
3. Modify programming code:
Press 0 + new programming code + # + repeat the programming code + # + *
﹙
Code: 6 Random digits
﹚
4. Add User Card
Press * + programming code + # + 1 + read card ...+ # + *
Notice: If need to add more user card,please read the user card continuously,at most
support 2000 user cards.There will be a default password 1234 when added user card,but
this password can’t be open the door,only for modifying the user password.
5.Delete user cards:
(1) Press 2 + read card...+ # + * Delete all read cards
(2) Press 20000 + # + * Delete all user cards
6. Setup unlock way
：
（
1
）
Press 30+ # Read valid cards unlock
（
2
）
Press 31 + # Read valid cards and input valid code unlock
（
3
）
Press 32 + # Read valid cards or input valid code unlock (Factory default)
7. Setup unlock delay time
Press 4 + Time + # + * can set 0-99 seconds,factory default: 5s
8. Security mode
：
（
1
）
Normal mode
（
Factory default
）
Press 70 + #
（
2
）
Locked mode
Press 71 + #
（
Note: Within 10 minutes,use 10 invalid cards consecutively or use invalid
code 10 times, the system will dead lock 10 minutes
）
（
3
）
Alarm mode
Press 72 + #
（
Within 10 minutes,use 10 invalid cards consecutively or use invalid code
10 times,the buzzer will be alarmed)
