Pneumatech AD-1500 Owner'S Manual Download Page 16

Page: 16 / 20

Pub. No. OM-A-75 REV. 4 — March 2006

REFRIGERATED AIR DRYER SERVICE CHECKLIST

Please get answers to as many questions as you can before writing or calling for service.

Customer’s Name ____________________________________________________________________________________

Phone no. ____________________________________

Fax no. ____________________________________________

Model no.____________________________________ Serial no. ___________________________________________

Voltage L1 ___________ L2 _________________ L3 _______________ PH ______________ HZ ______________

Amp draw

L1 ___________________________ L2 _______________________ L3 __________________________

Actual air flow (SCFM) _________________________

HP _________________________________________________

Description of problem

____________________________________________________________________________________________________

Air in temperature (°F) ________________________________________________________________________________

Air out temperature (°F) _______________________________________________________________________________

Air in pressure (PSIG) _________________________________________________________________________________

Air out pressure (PSIG) ________________________________________________________________________________

Refrigerant suction pressure when unit is operating (PSIG) __________________________________________________

Refrigerant suction pressure when unit is not operating (PSIG)_______________________________________________

10. Refrigerant discharge pressure when unit is operating (PSIG) _______________________________________________

11. Inspect refrigerant suction line at the outlet of air to refrigerant heat exchanger:

Cold ______________________ Hot ___________________ Temperature (°F) _________________________________

12. Inspect refrigerant suction line at inlet of compressor: Temperature (°F) _______________________________________

13. Oil pressure when unit is operating (PSIG) _______________________________________________________________

14. Separator skin temperature (°F)_________________________________________________________________________

15. Location of unit

Indoor_________________________ Outdoor_________________________________________

Clean _________________________ Dusty ___________________________________________

16. Ambient temperature (°F) ________________ Air-cooled condenser clean? Yes ________________ No ___________

17. a. Water-cooled condenser: City ____________________________ Tower_____________________________________

b. Inlet water temperature (°F) _____________________ Outlet water temperature (°F) _________________________

c. Inlet water pressure (PSIG) ___________________Outlet water pressure (PSIG) _______________________________

18. Inspect auto drain, operation: Stuck open ____________________ Stuck closed _____________________________

NOTE:

Maintenance Personnel, Copy This Page, Fill In Form and Fax to 262-658-1945

Summary of Contents for AD-1500





















Search results

Summary of Contents for AD-1500

Reviews:

Related manuals for AD-1500

Brands by name

Popular brands

Pneumatech AD-1500, Owner'S Manual

Search results

Summary of Contents for AD-1500

Reviews:

Related manuals for AD-1500

Brands by name

Popular brands