manualshive.com logo in svg

Plymovent Vertical Stack Rail System, Product User Manual

Share
Download
Plymovent Vertical Stack Rail System Product User Manual Download Page 18

PUM_VSR_100209_EN

18/20

0

4.  Change of rubber seal:

 

Unscrew the catcher (A) from the VSR profile (B). 
Pull of the old rubber seal (C). 
Before mounting the new rubber seal they must be greased with liquid soap. 
Mount back the catcher (A) on the VSR profile.

5.  Trolley change:

 

Start by dismounting the spring (D). 
Unscrew the stopbolt (E) on the horizontal support, C-profile.  
Pull carefully the rail to the side until the support trolley (F) appears.  
Note! Be careful when pulling the rail to the side to avoid both support trolleys to slide out of 
the hori-zontal support leg. Unhook the safety hook (G) from the support trolley and change 
the support trolley to a new one. Hook the safety hook onto the new support trolley, and push 
the rail back in the normal position. Refit the stopbolt (E) and the spring (D). Check that the rail 
moves smoothly in the support.

6.  Change of rubber gate (h)

 

Unscrew the old rubber gate (H). 
Mount the new rubber gate in the same position.

D

B

C

E

G

A

H

F

8. 

MAINTENANCE INSTRUCTION  

Summary of Contents for Vertical Stack Rail System





















Reviews:

No comments

Brands by name

Popular brands

Load more brands