Plymovent FLEX-3 Installation And User Manual Download Page 11

0507270010/020821/D Flex-3 | Flex-4 | UltraFlex-3 | UltraFlex-4 

10

Fig. 6.5 

A

B

Hinge of the wall/unit side

6.3 

Lubrication of the rotating hinge

To make sure that the rotating hinge can turn freely, you must 

lubricate the axle regularly.

Fig. 6.6

•  (B) Apply grease into the grease nipple with a grease gun.

Recommended grease type: standard EP2 bearing grease

Fig. 6.6 

B

Lubrication of the rotating hinge

TROUBLESHOOTING

If the product does not function (correctly), consult 

the checklist below to see if you can remedy the 

error yourself. Should this not be possible, contact 

your supplier.

WARNING!

Obey the safety regulations that are written in

chapter 3 when you carry out the activities below.

Symptom

Problem

Possible 

cause

Solution

General

Extraction 

capacity is 

insufficient

Pollution of 

the facility

Throttle valve is 

closed

Open the throttle 

valve

Flexible hose(s) 

torn or loose

Replace flexible 

hose(s) or install 

correctly

Rubber seal(s) 

torn or installed 

incorrectly

Replace rubber 

seal(s) or install 

correctly

Outside air is 

extracted into 

the connected 

duct system

Make the duct 

system airtight

Symptom

Problem

Possible 

cause

Solution

Extraction 

hood not in 

balance

Hood does 

not stay in 

the desired 

position

Not enough 

friction

Adjust the friction 

of the hood hinge; 

refer to paragraph 

6.2.1

You cannot 

move the 

hood in the 

desired 

position

Too much 

friction

Entire arm 

(both arm 

sections) falls 

down

Arm does not 

stay in the 

desired 

position

Spring tension 

too low

Increase the spring 

tension of the hinge 

at the wall/unit 

side; refer to 

paragraph 6.2.3

Flex-3 | Flex-4

Extraction 

arm creaks or 

squeaks

Arm does not 

move 

smoothly

Insufficient 

lubrication

Lubricate the hinge 

points; refer to Fig. 

IV (C) on page 

13

Movement 

problem of 

the hood side 

of the arm

Friction in the 

middle hinge

Not enough 

friction due to 

aging

Adjust the friction 

in the middle 

hinge; refer to 

paragraph 6.2.2 

(Flex arms)

Too much 

friction
Too much 

friction due to 

pollution

Clean the friction 

mechanism in the 

middle hinge

UltraFlex-3 | UltraFlex-4

Extraction 

arm creaks or 

squeaks

Arm does not 

move 

smoothly; 

excessive 

wear of parts

Insufficient 

lubrication

Lubricate the hinge 

points; refer to Fig. 

V (C) on page 14
Lubricate the steel 

cable near the 

BalanceWheel; 

refer to Fig. V (B) 

on page 14

The hood side 

of the arm 

falls down

Arm does not 

stay in the 

desired 

position

Spring tension 

too low

Increase the spring 

tension; refer to 

paragraph 6.2.2 

(UltraFlex arms) 

SPARE PARTS

The following spare parts are available for the 

products;

8.1 

Flex-3 | Flex-4

Refer to exploded view Fig. VI on page 15 and the spare 

parts list on page 16

8.2 

UltraFlex-3 | UltraFlex-4

Refer to exploded view Fig. VII on page 17 and the spare 

parts list on page 18

DISPOSAL

After life of the product, dispose of it in accordance 

with federal, state or local regulations.

Summary of Contents for FLEX-3





















Reviews: