0507210010/010320/D FAN-28
4
- Do not install the product in front of entrances and exits that
must be used for emergency services.
- Mind any gas and water pipes and electric cables.
- Make sure that the workspace is well illuminated.
- Stay alert and keep your attention to your work. Do not
install the product when you are under the influence of
drugs, alcohol or medicine.
- Air containing particles such as chromium, nickel, beryllium,
cadmium, lead etc., should never be recycled. This air must
always be brought outside the working area.
Use
WARNING!
Fire hazard! Do
not
use the product for:
- polishing applications in combination with
grinding, welding or any other application that
generate sparks
(fibers from polishing or abrasive flap disks
are highly flammable and pose a high risk of filter fires when
exposed to sparks)
- arc-air gouging
-
extracting flammable, glowing or burning particles
or solids or liquids
- extracting of aggressive fumes (such as
hydrochloric acid) or sharp particles
- extracting dust particles that are released when
welding surfaces treated with primer
- sucking cigarettes, cigars, oiled tissues, and other
burning particles, objects, and acids
WARNING!
Explosion hazard! Do
not
use the product for
explosion-hazardous applications, e.g.:
- aluminium laser cutting
- grinding aluminium and magnesium
- explosive environments or explosive substances/
gases
WARNING!
Do
not
use the product for:
- extraction of hot gases (more than 70°C/158°F
continuously)
-
flame spraying
- oil mist
- heavy oil mist in welding fume
- extraction of cement, saw dust, wood dust etc.
- Inspect the product and check it for damage. Verify the
functioning of the safety features.
- During use, always use Personal Protective Equipment (PPE)
to avoid injury. This also applies for persons who enter the
work area.
- Check the working environment. Do not allow unauthorised
persons to enter the working environment.
- Protect the product against water and humidity.
-
Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
- Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers (suitable for
fire classes ABC).
- Do not leave any tools or other objects in or on the unit.
Service, maintenance and repairs
- Always use Personal Protective Equipment (PPE) to avoid
injury. This also applies for persons who enter the work area.
- Do not leave any tools in or on the product.
-
Use sufficient climbing gear and safety guards when working
on a higher level than 2 metres (local restrictions may
apply).
ATTENTION
Fully disconnect the fan from the main before you
carry out service, maintenance and/or repair jobs.
Personal protective equipment (PPE)
Wear respiratory protection and protective
gloves during service, maintenance and
repairs.
4
INSTALLATION
4.1
Tools and requirements
You need the following tools and requirements to
install the fan:
- basic tools
- electrical tools
4.1.1 To be sourced locally
- Hardware to install the mounting brackets
NMB or TNB
- Mains cord
4.2
Unpacking
Make sure that the product is complete. The
package contains:
- extraction fan
- mounting material to install the fan on the wall brackets NMB
or TNB
4.3
Mounting
The mounting instructions of the fan depend on the selected
wall bracket.
In case of mounting brackets type NMB, proceed with
paragraph 4.3.1.
In case of mounting brackets type TNB, proceed with
paragraph 4.3.2.
4.3.1 Mounting brackets NMB
• Install the NMB as described in the corresponding manual.
• Instal the extraction arm as described in the corresponding
manual.
•
Install the fan (B) on the rotating flange (C) of the
extraction arm with the supplied mounting material.
•
Tighten the bolts firmly.
•
Make sure that the seal between the conection flange and
the fan is airtight.
Subsequently:
• Connect the outlet opening (A) of the fan to:
- a spiral tube (Ø 160 mm); or
-
a flexible hose Ø 160 mm (CKS; ref. paragraph 1.4)
• Make sure that all connections are airtight.
