background image

OPERATION INSTRUCTIONS

·

The

 

FRES

LED

100

 

is

 

an

 

LED

 

stage

 

light

 

for

 

on-site

 

decoration

 

purpose.

·

Don't turn on the fixture if it's been through severe temperature difference like after transportation

because it might damage the light due to the environment changes. So make sure to operate the

fixture until it is in normal temperature.

·

This light should be keep away from strong shaking during any transportation or movement.

·

Don't pull up the light by only the head, or it might cause damages to the mechanical parts.

·

Don't expose the fixture in overheat, moisture or environment with too much dust when installing

it. And don't lay any power cables on the floor. Or it might cause electronic shock to the people.

·

Make sure the installation place is in good safety condition before installing the fixture.

·

Make sure to put the safety chain and check whether the screws are screwed properly when

installing the fixture.

·

Make sure the lens are in good condition. It's recommended to replace the units if there are any

damages or severe scratch.

·

Make sure the fixture is operated by qualified personnel who knows the fixture before using.

·

Keep the original packages if any second shipment is needed.

·

Don't try to change the fixtures without any instruction by the manufacturer or the appointed

repairing agencies.

·

It is not in warranty range if there are any malfunctions from not following the user manual to

operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.

INSTALLATIONS

For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas

were the fixture might be reached by unauthorized personnel.

Before mounting the fixture to any surface, make sure that the installation area can hold a

minimum point load of 10 times the device's weight.

Fixture installation must always be secured with a secondary safety attachment, such as an

appropriate safety cable.

Never stand directly below the device when mounting, removing, or servicing the fixture.

From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at

least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

7

8

FRESLED-PL

1

00

Summary of Contents for FRESLED 100














Reviews: