background image

6

This log set has been tested and approved to ANSI Z21.11.2-2013 standard for Unvented Heaters 

and can be operated with the flue damper closed. State and local codes in some areas prohibit the 

use of vent-free heaters. 

DUAL FUEL CAPABILITY

Your heater is equipped to operate on either propane or natural gas. The heater is

shipped from the factory ready for connecting to propane. The heater can easily be

changed to natural gas by having your qualified installer follow the instructions on page

16 and the markings on the heater.

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air and cuts off main burner gas in the 

event of flame out.

ELECTRIC PUSH BUTTON IGNITION SYSTEM

This heater is equipped with an electronic piezo control system. This system requires

one AAA battery (provided).

THERMOSTAT HEAT CONTROL

The control automatically cycles the burner on and off to maintain a desired room temperature (See 

page 23). When used as a vented decorative appliance, use of the thermostat function is prohibited, 

operate manually only.

 

  State of Massachusetts: 

The installation must be made by a licensed plumber or gas fitter in 

  the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-fired 

  supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale 

  of the unit.

  In the State of Massachusetts, unvented propane or natural gas-fired space heaters shall 

  be prohibited in bedrooms and bathrooms.

  In the State of Massachusetts the gas cock must be a T-handle type. The State of 

  Massachusetts requires that a flexible appliance connector cannot exceed three feet

  in length.

LOCAL CODES

Install and use heater with care. Follow all codes. In the absence of local codes, use the latest edi-

tion of The National Fuel Gas Code, ANSI Z223.1, also known as NFPA 54*.

*Available from:

American National Standard Institute, Inc. 

 National Fire Protection Association, Inc.

1430 Broadway  

 

 

 

 

1 Batterymarch Park

New York, NY 10018  

 

 

 

Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit the use 

of vent-free heaters.

PRODUCT FEATURES

The installation of appliances designed for manufactured home (U.S. only) or mobile home 

installation must conform with the 

Standard CAN/CSA Z240 MH, Mobile Housing

, in Canada, 

or with the 

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280

in the United States, or when such a standard is not applicable, 

ANSI/NCSBCS A225.1/NFPA 

501A, Manufactured Home Installations Standard

.

Summary of Contents for VFL-CO18DT


































Reviews: