background image

8

PREPARING FOR INSTALLATION

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space:

 Includes the room in which you will install heater plus any adjoining rooms with

doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space Length × Width × Height = cu. ft. (volume of space)

  Example: Space size 20 ft. (length) × 16 ft.(width) × 8 ft. (ceiling height) = 2560 cu. ft. (volume 

  of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these 

rooms to the total volume of the space.

2. Divide the space volume by 50 cu. ft. to determine the maximum BTU/hr the space can support.

  _______ (volume of space) ÷ 50 cu. ft.= (Maximum BTU/hr the space can support)

  Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum BTU/hr the space  

  can support)

3. Add the BTU/hr of all fuel burning appliances in the space.

  Vent-free heater _________ BTU/hr

  Gas water heater* ________BTU/hr

  Gas furnace _____________BTU/hr

  Vented gas heater ________BTU/hr Example:

  Gas heater logs __________BTU/hr Gas water heater 30,000 BTU/hr

  Other gas appl ____BTU/hr Vent-free 26,000 BTU/hr

  Total = ____BTU/hr Total = 56,000 BTU/hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the

 outdoors and vents to the outdoors.

4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.

  _______ BTU/hr (maximum the space can support)

  _______ BTU/hr (actual amount of BTU/hr used).

  Example : 51,200 BTU/hr (maximum the space can support) 56,000 BTU/hr (actual amount of 

  BTU/hr used)

The space in the above example is a confined space because the actual BTU/hr used is more than 

the maximum BTU/hr the space can support.

You must provide additional fresh air. Your options are as follows:

a) Rework worksheet, adding the space of an adjoining room. If the extra space provides an 

  unconfined space, remove door to adjoining room or add ventilation grills between rooms. See  

  “Ventilation Air From Inside Building,” page 9.

b) Vent room directly to the outdoors. See “Ventilation Air From Outdoors”, page 9.

c) Install a lower BTU/hr heater if lower BTU/hr size makes room unconfined. If the actual BTU/hr  

  used is less than the maximum BTU/hr the space can support, the space is an unconfined space. 

  You will need no additional fresh air ventilation.

Summary of Contents for VFL-CO18DT


































Reviews: