pleasant hearth 23-29-65, Manual

Page: 9 / 40

1
6
4
5
PACKAGE CONTENTS
2 3
9
C
Questions, problems, missing parts?
Before returning to your retailer, call our customer
service department at 1-877-447-4768, 8:30 a.m. - 4:30 p.m., CST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
A
HARDWARE CONTENTS (shown actual size)
ASSEMBLY INSTRUCTIONS
1. Screw each of the four legs (Q) into the
predrilled holes in each corner of the base (C).
Screw middle leg (R) into predrilled hole in
center brace of base (C).
2. Insert two dowels (DD) into predrilled holes on
each end of shelf rail (F). Slip one end of shelf
rail (F) into predrilled holes in upper edge of
left inner panel (J) and the other end into
predrilled holes in upper edge of right inner
panel (K). Press together until both joints are
snug. Lay base (C) face up on a flat, level surface
and insert four dowels (DD) into predrilled
holes in center area of base (C). Slip panel
assembly over dowels (DD) so that the dowels
(DD) fit into predrilled holes in bottom edge of
assembly. Insert two bolts (AA) through flat
washers (BB), lock washers (CC), predrilled
holes in edge blocks and into predrilled holes
in base (C). Tighten with Phillips screwdriver
(not included).
Repeat on opposite side.
1
2
Q
ITEM #0000000
MODEL #23-29-65
HERITAGE MEDIA MANTEL
FOR 23 IN. FIREBOX
Français p. 11
Español p. 22
B
C
D
E
PART DESCRIPTION QUANTITY
A Top Panel 1
B Top Shelf 1
C Base 1
D Adjustable Shelf 2
E Top Shelf Divider 1
F Shelf Rail 1
G Left Side Panel 1
H Right Side Panel 1
J Left Inner Panel 1
K Right Inner Panel 1
L Lower Back Panel 2
M Upper Back Panel 1
N Left Cabinet Door 1
P Right Cabinet Door 1
Q Leg 4
R Middle Leg 1
Bolt
Qty. 20
AA
BB
Flat
Washer
Qty. 20
CC
Dowel
Qty. 22
SAFETY INFORMATION
PREPARATION
Please read and understand this entire manual before attempting to assemble, operate or install
the product.
WARNING
• Mantel is heavy and should be assembled near its desired location.
• It is recommended that two people move the finished mantel to prevent injury.
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not
attempt to assemble the product.
Estimated Assembly Time: 45 minutes
Tools Required for Assembly: Phillips screwdriver (not included).
R
ONE YEAR LIMITED WARRANTY
If within one year from the date of original purchase this item fails due to a defect in material or
workmanship, we will replace or repair at our option, free of charge. To order parts or to obtain warranty
service, call 1-877-447-4768, Monday – Friday, 8:30 a.m. – 4:30 p.m., CST. This warranty does not
cover defects resulting from improper or abnormal use, misuse, accident, or alteration. Failure to follow
all instructions in the owner’s manual will also void this warranty. The manufacturer will not be liable for
incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion of incidental or consequential damages may
not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Variations in actual wood color and finishes which may result from natural characteristics of the wood,
such as grain patterns, mineral streaks and the like, are not considered defects. As wood continues to
move and age you may notice these slight differences in color, even on different parts of any individual
unit. Sound knots and slight surface cracks are true personality of a quality piece of wood furniture.
CARE AND MAINTENANCE
• To maintain the finish, clean with a soft, slightly damp cloth and buff with a dry cloth.
• Wood furniture should never be dragged across a floor. The added stress from dragging the unit
may cause the dragged edge to splinter or it may cause a joint to loosen.
ASSEMBLY INSTRUCTIONS
3. Insert two dowels (DD) into predrilled holes
in each end of top shelf (B). Slip one end of
top shelf (B) into predrilled holes on inside
face of left side panel (G) and the other end
into predrilled holes on inside face of right side
panel (H). Press together until both joints are
snug.
3
B
Hardware Used
x 4
AA
x 4
BB
x 4
CC
Bolt
Flat Washer
AA
BB
CC
Hardware Used
x 4
DD
Dowel
Wa r m i n g Yo u r H o m e. W a r m i n g Y o u r H e a r t.
Lock
Washer
Qty. 20
DD
F
G
H
Lock Washer
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at at 1-877-447-4768, 8:30 a.m. - 4:30 p.m.,
CST, Monday - Friday.
10
PART DESCRIPTION PART #
A Top Panel 20-12-178
B Top Shelf 20-12-179
C Base 20-12-180
D Adjustable Shelf 20-12-181
E Top Shelf Divider 20-12-182
F Shelf Rail 20-12-183
G Left Side Panel 20-12-184
H Right Side Panel 20-12-185
J Left Inner Panel 20-12-186
K Right Inner Panel 20-12-187
L Lower Back Panel 20-12-188
M Upper Back Panel 20-12-189
N Left Cabinet Door 20-12-190
P Right Cabinet Door 20-12-191
Q Leg 20-12-192
R Middle Leg 20-12-193
AA Bolt 20-12-194
BB Flat Washer 20-12-195
CC Lock Washer 20-12-196
DD Dowel 20-12-197
EE Screw 20-12-198
FF Knob Screw 20-12-199
GG Cabinet Door Knob 20-12-200
HH Shelf Support 20-12-201
Printed in China
20-10-128
4. Insert four dowels (DD) into predrilled holes
in base (C). Insert four dowels (DD) into
predrilled holes in top edge of left and right
inner panels (J&K). Set top shelf assembly
over dowels (DD) in base (C) and inner panel
assembly so that the dowels (DD) fit into
predrilled holes in bottom edges of left and
right side panels (G&H) and underside of top
shelf (B). Press down until all joints are snug.
4
Hardware Used
J
ASSEMBLY INSTRUCTIONS
5. Insert two bolts (AA) through flat washers (BB),
lock washers (CC), predrilled holes in edge
blocks and into predrilled holes in base (C).
Tighten with Phillips screwdriver (not included).
Repeat on opposite side.
5
CC
BB
AA
Hardware Used
x 4
AA
x 4
BB
Bolt
Flat Washer
Lock Washer
x 4
CC
6. Lay assembly on its back. Insert four bolts (AA)
through flat washers (BB), lock washers (CC),
predrilled holes in edge blocks and into predrilled
holes on right side of assembly as illustrated.
Tighten with Phillips screwdriver (not included).
Repeat on opposite end.
6
Hardware Used
x 8
AA
x 8
BB
x 8
CC
Bolt
Flat Washer
AA
BB
CC
Lock Washer
C
DD
G
B
N
J
M
D
L
K
L
Screw
Qty. 62
EE
FF
Knob
Screw
Qty. 2
GG
Shelf
Support
Qty. 8
Cabinet
Door Knob
Qty. 2
HH
AA BB CC
DD
EE
FF
GG
HH
x 8
DD
Dowel
J
K
DD
G
H
K
C
H
x 8
DD
Dowel
DD
8
7
ASSEMBLY INSTRUCTIONS
7. With assembly sitting upright, insert two
dowels (DD) into predrilled holes in top of
top shelf (B). Slip top shelf divider (E) over
dowels (DD) so that the dowels fit into
predrilled holes in bottom edge. Press
down until snug.
7
E
Hardware Used
8. With assembly sitting upright, insert six
dowels (DD) into predrilled holes in top of
edges of assembly. Slip top panel (A) over
dowels (DD) so that the dowels fit into
predrilled holes in underneath side of top
panel (A). Insert two bolts (AA) through flat
washers (BB), lock washers (CC), predrilled
holes in edge blocks,and into predrilled holes
in top panel (A). Tighten with Phillips screwdriver
(not included).
Repeat on opposite side.
8
Hardware Used
DD
A
ASSEMBLY INSTRUCTIONS
9. Attach upper back panel (M) and lower back
panels (L) by inserting screws (EE) into
predrilled holes and tightening with Phillips
screwdriver (not included).
9
Hardware Used
11. Attach right cabinet door (P) to hinges on
assembly. Attach cabinet door knob (GG) with
knob screw (FF) inserted through predrilled hole
in right cabinet door (P). Tighten with Phillips
screwdriver (not included).
Repeat with left cabinet door (N).
11
Hardware Used
x 2
GG
x 2
FF
Cabinet
Door Knob
Knob Screw
FF
GG
P
H
x 62
EE
Screw
x 4
AA
x 4
BB
Bolt
Flat Washer
Lock Washer
x 4
CC
DD
G
N
C
P
Q
R
A
B
C
D
E
F
G
H
N
J
M
L
K
P
Q
R
DD
F
DD
AA
BB
CC
B
x 2
DD
Dowel
x 6
DD
Dowel
E
DD
AA
BB
CC
ASSEMBLY INSTRUCTIONS
10. Insert shelf supports (HH) into predrilled
holes as illustrated, keeping all shelf supports
(HH) parallel to each other. Lay adjustable
shelves (D) in place on each side of assembly.
10
D
D
HH
Hardware Used
x 8
HH Shelf Support
EE
L
M
L
L
100%
BLACK
FONT & SOFTWARE USAGE STATEMENT
COLOR USAGE & PRINT REQUIREMENTS
ALL INSTRUCTION MANUALS AND RELATED MATERIAL CREATED THROUGH
ADAPTATION OF THESE TEMPLATES MUST BE APPROVED BY LOWE’S
BRAND PACKAGING DEPARTMENT PRIOR TO PRODUCTION.
CONTACT: BRAND PACKAGING DEPARTMENT, LOWE’S COMPANIES, INC.
ATTN: PACKAGING STANDARDS
1000 LOWE’S BOULEVARD, MAIL STOP: 4WTD
MOORESVILLE, NC 28117
704-758-2785
DO NOT USE ANY COLOR GRAPHICS OR PHOTOGRAPHY IN YOUR INSTRUCTION
MANUALS. INSTRUCTION MANUALS PRINT IN GREYSCALE ONLY.
ALL GRAPHICS SHOWN ARE FOR SIZE AND POSITION ONLY; FINAL LINE-ART GRAPHICS
ARE REQUIRED FOR RELEASE TO PRESS.
IMPORTANT VENDOR NOTE
VENDORS ARE RESPONSIBLE FOR THE EXECUTION AND ACCURACY OF THEIR
INSTRUCTION MANUALS. THEY ARE SOLELY RESPONSIBLE FOR INSERTING ALL OF THE
CORRECT LEGAL CERTIFICATION, WARNING, WARRANTY, AND OTHER APPLICABLE
PRODUCT INFORMATION. HARDWARE MUST BE SHOWN AS ACTUAL SIZE IN THE
HARDWARE CONTENTS SECTION WITH LINE ART DRAWING OF THE HARDWARE, THE
DIMENSIONS, NAME DESCRIPTOR AND QUANTITY. LOWE’S IS NOT RESPONSIBLE FOR
ANY INCURRED DESIGN, TRANSLATION OR PRINTING COSTS. PLEASE REFER TO THE
TRANSLATION REQUIREMENTS ON LOWESLINK.COM
• FONTS USED ON THIS FILE: SEE FONT LEGEND.
• CONTACT YOUR APPROPRIATE FONT VENDOR TO PURCHASE THE REQUIRED FONTS
FOR THIS PACKAGE LINE.
• ADOBE ILLUSTRATOR CS3 WAS USED TO CREATE THIS FILE.
LOWE’S REQUIRES EACH VENDOR TO OBTAIN THEIR OWN LINE-ART GRAPHICS. ALL INSTRUCTION MANUAL GRAPHICS WILL
BE APPROVED BY LOWE’S BRAND MANAGEMENT DURING PROOFING.
THIS DESIGN IS PROPRIETARY AND CONFIDENTIAL TO LOWE’S COMPANIES, INC. AND CANNOT BE COPIED OR OTHERWISE
REPRODUCED OR USED WITHOUT THE EXPRESS WRITTEN PERMISSION OF LOWE’S.
THESE ARE THE PANTONE COLORS THAT ARE USED IN THIS FILE.
THESE MUST BE USED WHEN CREATING ANY OTHER PACKAGING.
THE ADDITION OF OTHER SPOT COLORS IS NOT PERMITTED.
ARTWORK DISCLAIMERS
FONT LEGEND
ALL FONTS MUST BE ARIAL BOLD OR ARIAL REGULAR, 12 PT. (MINIMUM) ON 14 PT. LEADING UNLESS OTHERWISE SPECIFIED.
REQUIRED PAPER TYPE
USE THE FOLLOWING PAPER FOR YOUR INSTRUCTION MANUALS:
• PAPER BASIS WEIGHT: 20-lb. PAPER OR 75 GRAMS/SQ METER
• DOCUMENT SIZE: PRINTED TWO-SIDES ON TABLOID OR A3 AND FOLDS
TO LETTER SIZE OR A4. INCLUDE SAMPLE MOCK-UP TO INDICATE
FOLD(S) AND PAGE LAYOUT.
THIS COLOR IS USED FOR
NOTES AND DOES NOT
PRINT.
CALL OUTS
(DO NOT PRINT)
THIS COLOR INDICATES
ALL TEXT TO BE CHANGED
WITH PRODUCT SPECIFIC
TEXT.
EDITABLE TEXT
(DO NOT PRINT)