manualshive.com logo in svg

PlayNation Play Systems 1501, Assembly Instructions Manual

Share
Download
PlayNation Play Systems 1501 Assembly Instructions Manual Download Page 139

STEP 22: ROOF SUPPORT ASSEMBLIES

1: LOCATE FOUR 2 X 4 X 51-1/8" ROOF SUPPORT (LEFT), FOUR 2 X 4 X 51-1/8" ROOF SUPPORT (RIGHT) AND FOUR 5/4 

X 6 X 10" ROOF PEAK SUPPORT PIECES.

2: FIND A FLAT SURFACE TO WORK ON. LAY THE ROOF SUPPORTS DOWN ON THE FLAT SURFACE WITH THE 

COUNTERSUNK HOLES FACING UP. ALIGN THE ANGLED ENDS OF THE ROOF SUPPORTS FLUSH WITH ONE ANOTHER. 

PLACE A ROOF PEAK SUPPORT ON TOP OF THE ROOF SUPPORTS AS SHOWN. THE EDGES SHOULD BE FLUSH WHERE 

SHOWN BELOW.

3: USE FOUR #8 X 2" WOOD SCREWS TO ATTACH THE ROOF PEAK SUPPORT TO THE ROOF SUPPORTS AS SHOWN 

BELOW.

4: MAKE ONE MORE ROOF SUPPORT ASSEMBLY BY REPEATING 2 AND 3.

ROOF SUPPORT - RIGHT

2 X 4 X 27" 

2 X 4 X 27"

ROOF SUPPORT - LEFT

COUNTERSUNK HOLE FACES UP

5/4 X 6 X 10"

ROOF PEAK 

SUPPORT

B

#8 X 2"

WOOD SCREW

SCALE 1 : 3

DETAIL B

FLUSH

FLUSH

FLUSH

COMPLETED ROOF 
SUPPORT ASSEMBLY 
(MAKE 2)

129

Summary of Contents for 1501






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands