manualshive.com logo in svg

Playcore SPECTRUM Aquatics Motion Trek 400, Manual

Share
Download
Playcore SPECTRUM Aquatics Motion Trek 400 Manual Download Page 2

1 

800.791.8056 

▪

 www.spectrumproducts.com 

You have purchased a Spectrum Products Motion Trek 400 assisted access lift. Providing the 
unit is installed correctly and properly maintained, it will furnish you with many years of trouble- 
free use. It is important to read this entire manual prior to assembly or operation. 

Shipping Information: 

Each lift will arrive partially assembled in one box. Before accepting the lift from the carrier, 
inspect for visible damage and match the contents with those listed below. Spectrum is not 
responsible for lost or damaged freight. 

The box will contain all structural components and hardware. The following is a list of the 
components included with your shipment from Spectrum. Use Components and Hardware 
Figure, Page 2, as a reference to identify each item listed. 

1 

Mast & Boom assembly 

2 

Seat Halves 

1 

Actuator 

1 

Footrest assembly 

1 

Seat Belt 

1 

Battery 

1 

Seat pole assembly 

1 

Handset 

1 

Charger 

2 

Flip-Down Armrest Assemblies 

1 

General Hardware 

1 

Anchor 

 

 

 

Summary of Contents for SPECTRUM Aquatics Motion Trek 400














Reviews:

No comments

Brands by name

Popular brands

Load more brands