Playcore SPECTRUM Aquatics Motion Trek 400 Manual Download Page 11

10 

800.791.8056 

 www.spectrumproducts.com 

Lowering: 

Pressing the down (

˅

) arrow causes the seat to lower. The seat will continue to lower while the 

button is pressed or until the lift reaches its lowest extent. If the button is released, the lift will 
stop moving downward. 

Clockwise Rotation: 

Pressing the right (˃)

 arrow causes the seat to rotate clockwise. The seat will continue to rotate 

while the button is pressed. If the button is released, the lift will stop rotating clockwise.  

Counterclockwise Rotation: 

Pressing the left (˂)

 arrow causes the seat to rotate counterclockwise. The seat will continue to 

rotate while the button is pressed. If the button is released, the lift will stop rotating 
counterclockwise.  

To enter the Pool or Spa: 

A. Position the chair of the lift over the deck in a suitable position for a transfer using

the directional buttons on the transmitter

B. Carefully transfer into the lift seat from mobility device
C. Fasten seat belt
D. Rotate the lift over the water, where it will not come into contact with the pool edge

or any obstruction using the left or right buttons on the transmitter

E. Lower the lift into the water until buoyant by pushing the down button
F. Unfasten seat belt and carefully move away from the lift
G. Using the directional buttons on remote return lift chair to an on deck position not

over the pool

To Exit the Pool or Spa: 

A. Recall lift chair into water to the previous depth and position upon transferring from

the lift seat to the pool using directional arrows

B. Carefully transfer into the lift seat from water
C. Fasten seat belt
D. Lift the seat straight up using the up directional arrow on the transmitter until top of

lifting stroke is reached

E. Rotate the chair into a suitable position on deck to transfer from lift seat
F. Unfasten seat belt
G. Carefully Transfer from lift seat into mobility device

Battery Charging & Installation 

The battery comes partially charged, but will need charging after the first several hours of use.  
Charging time is approximately 12 hours for the first few charges, four hours after the first two 
full battery cycles. The lift comes with a battery charger for use in dry locations.  Charge the 
battery as follows: 

Summary of Contents for SPECTRUM Aquatics Motion Trek 400














Reviews: