manualshive.com logo in svg

Playcore SPECTRUM Aquatics Freedom Lift 57961, Manual

Share
Download
Playcore SPECTRUM Aquatics Freedom Lift 57961 Manual Download Page 14

13

Troubleshooting

Problem:

Cause:

Solution:

1.  Lift will not operate at all:

Low Battery (Lift) – Red or 

amber LED on the receiver

Damaged Battery (Lift) – Red 

LED on the receiver

Dead Battery (Transmitter)

Remote Locked

Battery Fuse blown

Battery Push button Switch in 

the off (out) position

Recharge Battery

Replace Battery*

Replace Battery

3V Lithium 2032

Push unlock button for 

2 seconds

Replace Battery Fuse

Depress push button 

switch into the on (in) 

position

2. The seat will not raise or lower.

The seat will not rotate.

Low battery (Amber LED on 

Receiver)

Battery not installed properly

Receiver malfunction

Recharge battery

Reinstall battery

Replace Receiver*

3. The seat’s motion isn’t smooth or 

sticks at a certain point during travel.

Excessive wear to bearings

Excessive wear to Actuator

Replace bearings*

Replace Actuator*

4. The seat travels much slower 

than normal.

Low battery

Defective or worn-out battery

Recharge battery

Replace battery*

5. The lift makes much more noise 

or unusual noises during operation.

Excessive wear to bearings

Pivot points galling 

Replace bearings*

Oil pivots with light oil 

(3-1)

6.  Battery will not charge:

Charger Fuse Blown

Bad Battery (red LED on 

charger – not turning orange 

or green in 4 hours or less)

Replace Charger Fuse

Replace Battery*

*Please contact your local distributor or Spectrum Customer Service to order parts 406.532.6321

Summary of Contents for SPECTRUM Aquatics Freedom Lift 57961















Reviews:

No comments

Brands by name

Popular brands

Load more brands