Home
/
Plasma
/
IBEAM FC
/
Manual

Plasma IBEAM FC, Manual, Page: 47 / 60

Share

32 pages before
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60

Page: 47 / 60

Plasma IBEAM FC Manual Download Page 47

44

Serial command:

NE

Description: Enable or disable the E-24 error for E/B ratio.
Usage:

NE(0 or 1)<cr>. 0 enables, and is the default. 1 disables.

Example:

Send “NE1<cr>”. The E-24 error alarm will be disabled. When the emission to
beam ratio is not met, the E-24 error will not flash or function.

Response:

<lf><cr>OK<lf><cr><eot>

Serial command:

NI

Description: Set the neutralizer filament current.
Usage:

NI(0.0-20.0)<cr>

Example:

Send “NI5.1<cr>”. The neutralizer filament current will bet set to 5.1 A. After the
source is turned on the power supply will ramp the neutralizer filament current to

5.1 A. Acceptable range is from 0.0 to 20.0 A. The source check-out sheet should
be consulted for normal ranges.

Response:

<lf><cr>OK<lf><cr><eot>

Serial command:

NK

Description: Enable or disable lock-out of the front panel keypad. The keypad lock-out will

disable all switches on the front panel, and no alarms will sound.

Usage:

NK(0 or 1)<cr>. 1 enables the keypad Lockout, 0 disables the lockout, restoring

user access via keypad, as well as the alarm buzzer.

Example:

Send “NK1<cr>”. The keypad switches will be locked, allowing no input from the

front panel. The power supply must be run from an externally connected input
device, such as a deposition system or connected computer.

Response:

<lf><cr>OK<lf><cr><eot>

Serial command:

NL

Description: Set the neutralizer filament current limit.
Usage:

NL(0.0-20.0)<cr>

Example:

Send “NL8.5<cr>”. The neutralizer filament current limit will be set to 8.5 A. If
the neutralizer current exceeds 8.5 A, an alarm will trigger. Acceptable range is from

0.0 to 20.0 A. The source check-out sheet should be consulted for typical ranges of
neutralizer filament current. The limit should be set slightly higher than the

maximum expected neutralizer filament current.

Response:

<lf><cr>OK<lf><cr><eot>

«
...
45
46
47
48
49
...
»

Summary of Contents for IBEAM FC





























































Reviews:

No comments