Planika GUSTAV Gas Installation And User Manual Download Page 16 | Manualshive

Page: 16 / 20

background image

Copyright Planika Sp. z o.o.

www.planikafires.com

IG0263#04

21.02.2020

16

4.3

Device shutdown

•

To turn off the device, simultaneously press and turn the knob all the way clockwise (Photo 8). The gas supply

will be cut and the flame on burner will be turned off.

Photo 8

•

Additionally, close also the valve on the gas cylinder.

4.4

Replacing the battery

If the battery is inserted incorrectly, the electronic ignitor may be irreparably damaged. Only replace the battery when

the appliance has been completely switched off.

The battery is placed in the container located on the control pane next to the flame regulation knob

•

Unscrew the ignition button

«
...
14
15
16
17
18
...
»

Summary of Contents for GUSTAV Gas





















Reviews:

No comments

Related manuals for GUSTAV Gas

Brand: IHP Pages: 8

Brand: Vanguard Pages: 30

Brand: Valor Pages: 26

Brand: Archgard Pages: 56

Antigua PIT1015A

Brand: Safavieh Furniture Pages: 3

Purefire Panoramic 5kw Slimline - SE

Brand: Ecosy+ Pages: 12

Brand: Whalen Pages: 52

Brand: Napoleon Pages: 4

Brand: Monessen Hearth Pages: 44

Brand: pleasant hearth Pages: 30

Brand: Vanguard Pages: 32

Brand: Outland Living Pages: 6

Brand: RealFlame Pages: 27

Brand: Sonnenkonig Pages: 48

Brand: Desa Pages: 28

Brand: eligent Pages: 4

Brand: Stellar Hearth Pages: 37

Brand: HAMPTON BAY Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands