Planet WDAP-1800AX User Manual Download Page 61

Page: 61 / 125

User Manual of WDAP-C1800AX &WDAP-1800AX

- 32 -

4.2 Network

The Network function provides WAN, LAN and network configuration of the router as shown in

Figure

4-25.

Figure 4-25:

Network Menu

Object

Description

WAN

Allows setting WAN interface.

LAN

Allows setting LAN interface.

UPnP

Disable or enable the UPnP function.

The default configuration is disabled.

Routing

Allows setting Route.

RIP

Disable or enable the RIP function.

The default configuration is disabled.

OSPF

Disable or enable the OSPF function.

The default configuration is disabled.

IGMP

Disable or enable the IGMP function.

The default configuration is disabled.

IPv6

Allows setting IPv6 WAN interface.

DHCP

Allows setting DHCP Server.

DDNS

Allows setting DDNS and PLANET DDNS.

Summary of Contents for WDAP-1800AX






























































































































Search results

Summary of Contents for WDAP-1800AX

Reviews:

Related manuals for WDAP-1800AX

Brands by name

Popular brands

Planet WDAP-1800AX, User Manual

Search results

Summary of Contents for WDAP-1800AX

Reviews:

Related manuals for WDAP-1800AX

Brands by name

Popular brands