background image

Server”

 

Error Message: 

For some reason (ex. All lines of this VoIP router are busy), here will 

display the failure information of last time VoIP Call in.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line Setting 

This page will setup the phone line information each port.   

 

Parameter Description

 

Port 

display FXS interfase the port number. 

Interface 

Telephone interface type: 

FXO: for connect to telephone line or PBX extension line. 

FXS: for connect to regulate phone set. 

Name 

Line name for this port. This will send and display on the remote side 

due VoIP call 

Line Number 

Telephone number assigned to this line. 

TxGain 

Transmitter Gain. This will adjust the speaker volume of local phone set. 

The adjust range is from +3 to -13dB. Higher value will cause louder 

sound come from local phone set. 

RxGain 

Receiver Gain. This will adjust the microphone volume of local phone 

set. The adjust range is from -3 to +13dB. Higher value will cause 

amplifier the sound get from local phone set. 

Inbound 

Enable or disable the VoIP call to Internet. Disable the inbound will not 

allow any call made call to Internet from phone set. 

Outbound 

Enable or disable the VoIP call from Internet. Disable the Outbound will 

not allow any call made call from Internet to phone set. 

Hotline 

When Enable, it will allow you to make a VoIP call without Key in any 

 

20

Summary of Contents for VIP-320




















































Reviews: