background image

Trademarks

Copyright 

 PLANET Technology Corp. 2003.

Contents subject to revise without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.  

All other trademarks belong to their respective owners.

Disclaimer

This  equipment  has  been  tested  and  found  to  comply  with  the  limits  for  a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference  in a 

residential installation, This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with the Instruc-

tion manual, may cause harmful interference to radio communications, how-

ever, there is no guarantee that interface will not occur in a particular instal-

lation. If this equipment does cause harmful interference to radio or television 

reception, which can be determined by turning the equipment off and on.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause 

radio interference, in which case the user may be required to take adequate 

measures.

Revision

Ethernet Over VDSL Converter User’s Manual

FOR MODELS: VC-102M / VC-102S

Part No.: EM-VC102

Summary of Contents for VC-102M



















Reviews: