Planet MAP-3100 Software Manual Download Page 115

Page: 115 / 124

PLANET Mesh Network Manager Guide

5.3.1.31 Management > SNMPD

This configuration page is used to alter the setting of the SNMP daemon in the Mesh AP unit.

The SNMP Access Table defines the access control of the SNMP management.

Parameters

1) Enable SNMP Management

•

A checkbox to enable or disable the SNMP management

2) Version

•

Define the SNMP version to use.

•

Available selection: Version 1 or 2c, Version 3 and All

3) Port

•

This field specifies the port used for SNMP management

•

Data type: Integer, default is 161

4) Read-Only

Community

•

The community keyword used for SNMP version 1 or 2c, which allow the

read accessing only.

PLANET Mesh Network Manager Guide

Page115 of 124

Summary of Contents for MAP-3100





























































































































Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands

Planet MAP-3100, Software Manual

Search results

Summary of Contents for MAP-3100

Reviews:

Related manuals for MAP-3100

Brands by name

Popular brands