background image

5

1. Introduction

1.1  Package Contents

Check the contents of your package for the following parts:

 

u

 Industrial 802.3at PoE Media Converter 

x 1

 

u

 User’s Manual 

x 1

 

u

 DIN-rail Kit 

x 1

 

u

 Wall Mounting Kit 

x 1

 

u

 RJ45 Dust Cap 

x 1

 

u

 SFP Dust Cap 

x 1

If any of these are missing or damaged, please contact your dealer 
immediately, if possible, retain the carton including the original packing 
material, and use them again to repack the product in case there is a 
need to return it to us for repair.

In the following section, the term 

“Industrial 802.3at PoE Media 

Converter”

 means the IGTP-802T/IGTP-802TS/IGTP-805AT.

1.2  How to Use This Manual

This Industrial 802.3at PoE Media Converter User Manual is 
structured as follows:

Chapter 2 Installation

The chapter explains the feature, functionality and the physical 
installation of the Industrial 802.3at PoE Media Converter.

Chapter 3 Link Passthrough

The chapter explains the link passthrough function of Industrial 802.3at 
PoE Media Converter.

Chapter 4 Troubleshooting

The chapter explains the troubleshooting of the Industrial 802.3at PoE 
Media Converter.

Summary of Contents for IGTP-802T





































Reviews: