background image

2.1.3 LED Indications 

There are 9 diagnostic LEDs located on the Front panel of industrial media converter. They provide 

real-time information of system and optional status. The following table provides description of the LED 

status and their meanings for the industrial media converter. 

LED  

Status 

Meaning 

Green 

When the IFT-802 has power input s the LED will light on 

Power 

Off 

No any power inputs 

Green Power 

on 

Power 1 

Off 

No power inputs 

Green Power 

on 

Power 2 

Off 

No power inputs 

Orange 

Power failure or UTP port failure or Fiber port failure 

Fault 

Off 

No Power failure or UTP port failure or Fiber port failure occurs or the 

port alarm disable 

Green 

The port is linking with its link partner. 

Blinks 

The port is transmitting or receiving packets from the FX device. 

LNK/ACT(Fiber) 

Off 

No device attached 

Orange 

The port is operating in full-duplex mode. 

FDX (Fiber) 

Off 

Half-duplex mode or no device attached 

Green 

In 100Mbps transmitting speed 

10/100(UTP) 

Off 

In 10Mbps transmitting speed 

Green 

The port is linking with its link partner. 

Blinks 

The unit is transmitting or receiving packets from the devices. 

LNK/ACT(UTP) 

Off 

No device attached 

Orange 

The port is operating in full-duplex mode. 

FDX (UTP)

 

Off 

Half-duplex mode or no device attached 

 

 

Summary of Contents for IFT-802



















Reviews: