background image

2.2 Rear Panel

The  rear  panel  of  the  FNSW-4800  indicates  an  AC  inlet  power  socket, 

which  accepts  input  power  from  100  to  240V  AC,  50-60Hz,  and  0.6A 

max.

Figure 2-2

  FNSW-4800 Switch rear panel

Note

1.  The  device  is  a  power-required  device,  it  means, 

it  will  not  work  till  it  is  powered.  If  your  networks 
should  active  all  the  time,  please  consider  using  UPS 
(Uninterrupted  Power  Supply)  for  your  device.  It 
will  prevent  you  from  network  data  loss  or  network 
downtime.

2.  In  some  area,  installing  a  surge  suppression  device 

may  also  help  to  protect  your  FNSW-4800  from 
being  damaged  by  unregulated  surge  or  current  to 
the FNSW-4800.

2.3 Hardware Installation

This  part  describes  how  to  install  your  FNSW-4800  and  make 
connections to the Switch. Please read the following topics and perform 
the  procedures  in  the  order  being  presented.  To  install  your  Switch  on 
a desktop or shelf, simply completed the following steps.

2.3.1 Desktop Installation

To install a Switch on a desktop or shelf, simply completed the following 
steps:

Step 1:  Attached the rubber feet to the recessed areas on the bottom 

of the Switch.

Step 2:  Place  the  Switch  on  a  desktop  or  shelf  near  an  AC  power 

source.

Step 3:  Keep  enough  ventilation  space  between  the  Switch  and  the 

surrounding objects.

Summary of Contents for FNSW-4800v2



















Reviews: