Planet Networking & Communication XGS3-24042 Page 10 Quick Installation Manual Download

Page: 10 / 16

7. Setting 1000BASE-X for SFP+ Port

The Managed Switch supports both

10GBASE-X

SFP+ transceiver and

1000BASE-X

SFP transceiver by manual setting and the default SFP+ port

speed is set to 10Gbps. To establish the fiber connection with 1000BASE-X SFP
transceiver, the following command configuration is required:

XGS3-24042

#config

XGS3-24042(config)

#interface ethernet 1/0/25-28

XGS3-24042(config-if-port-range)

#speed-duplex force1g-full

Figure 7-1

Setting 1000BASE-X Screen

8. Setting 100BASE-FX for SFP Port

The Managed Switch supports both

1000BASE-X

and

100BASE-FX

SFP

transceivers by manual setting and the default SFP port speed is set to 1000Mbps.
To establish the fiber connection with 100BASE-FX SFP transceiver, the following
command configuration is required:

XGS3-24042

#config

XGS3-24042(config)

#interface ethernet 1/0/21-24

XGS3-24042(config-if-port-range)

#speed-duplex force100-fx

Figure 8-1

Setting 100BASE-FX Screen

Summary of Contents for XGS3-24042

















Search results

Summary of Contents for XGS3-24042

Reviews:

Related manuals for XGS3-24042

Brands by name

Popular brands

Planet Networking & Communication XGS3-24042, Quick Installation Manual

Search results

Summary of Contents for XGS3-24042

Reviews:

Related manuals for XGS3-24042

Brands by name

Popular brands