Planet Networking & Communication wnap-7325 User Manual Download Page 18

Page: 18 / 95

User Manual of WNAP-7325/WNAP-7335

-17-

H/W Interface Definition

Object

Description

PoE LAN

(Passive PoE)

10/100Mbps RJ45 port , auto MDI/ MDI-X and passive PoE supported

Connect LAN port to the PoE injector to power on the device.

Pin assignment:
Pin 4, 5 (+)
Pin 7, 8 (-)

Pin 3 (Reset)

LAN 2

10/100Mbps RJ45 port , auto MDI/ MDI-X

Connect this port to the network equipment.

※

When the option “

Enable POE Pass Through

” on the System

Management page is checked, the LAN2 can supply passive PoE power to the

second WNAP-7325 or WNAP-7335 through LAN 2.

Reset

Press the

Reset

button on the device or on the PoE injector over 5

seconds to return to factory default setting.

※

If you have connected with the ELA-100, please DO NOT press the

reset button on the PoE injector to prevent the ELA-100 from being
damaged.

Table 2-2

The PoE Injector Indication

Summary of Contents for wnap-7325
































































































Search results

Summary of Contents for wnap-7325

Reviews:

Planet Networking & Communication wnap-7325, User Manual, Page: 18 / 95

Search results

Summary of Contents for wnap-7325

Reviews: