Planet Networking & Communication WGSW-48040HP Command Manual Download Page 298

Page: 298 / 386

Command Guide of WGSW-48040HP

Switch access-list rate limiter ID 5 is 1 pps

Switch access-list rate limiter ID 6 is 1 pps

Switch access-list rate limiter ID 7 is 1 pps

Switch access-list rate limiter ID 8 is 1 pps

Switch access-list rate limiter ID 9 is 1 pps

Switch access-list rate limiter ID 10 is 1 pps

Switch access-list rate limiter ID 11 is 1 pps

Switch access-list rate limiter ID 12 is 1 pps

Switch access-list rate limiter ID 13 is 1 pps

Switch access-list rate limiter ID 14 is 1 pps

Switch access-list rate limiter ID 15 is 1 pps

Switch access-list rate limiter ID 16 is 1 pps

GigabitEthernet 1/1 :

---------------------

GigabitEthernet 1/1 access-list action is permit

GigabitEthernet 1/1 access-list policy ID is 0

GigabitEthernet 1/1 access-list rate limiter ID is disabled

GigabitEthernet 1/1 access-list redirect is disabled

GigabitEthernet 1/1 access-list logging is disabled

GigabitEthernet 1/1 access-list shutdown is disabled

GigabitEthernet 1/1 access-list port-state is enabled

GigabitEthernet 1/1 access-list counter is 0

4.20.5 show access-list ace-status

Command:

show access-list ace-status [ static ] [ link-oam ] [ loop-protect ] [ dhcp ] [ ptp ]

[ upnp ] [ arp-inspection ] [ mep ] [ ipmc ] [ ip-source-guard ] [ ip-mgmt ] [ conflicts ]

[ switch <switch_list> ]

show

Show running system information

access-list

Access list

arp-inspection

The ACEs that are configured by ARP Inspection module

conflicts

The ACEs that did not get applied to the hardware due to hardware limitations

dhcp

The ACEs that are configured by DHCP module

ip-source-guard

The ACEs that are configured by IP Source Guard module

ipmc

The ACEs that are configured by IPMC module

link-oam

The ACEs that are configured by Link OAM module

-298-

Summary of Contents for WGSW-48040HP



































































































































































































































































































































































































Search results

Summary of Contents for WGSW-48040HP

Reviews:

Related manuals for WGSW-48040HP

Brands by name

Popular brands

Planet Networking & Communication WGSW-48040HP, Command Manual

Search results

Summary of Contents for WGSW-48040HP

Reviews:

Related manuals for WGSW-48040HP

Brands by name

Popular brands